Don't do what you see on the TV at Orange County Choppers, remember these guys were iron workers. I cringe everytime i see them beat ball bearings or roller bearings into there races to get something like the steering necks(example) together. Beating a bearing in the direction of the two races will put small dings into the races causing galling and fretting down the road besides binding when you try to steer or the shafts turn. "Do Not Do What They Do at Home"!!!!!!!!!!!!!!!!! I've tested so many gear boxes and seen bearings installed the wrong direction that failed in 1 or 2 days on the test dyne. Some of the ball bearings have opening were there assembled with the half moons in each mating race were if installed in the wrong direction this assembly opening gets hammered by the balls everytime a ball goes by the half moons. Its seening a side thrust load in that direction and if the bearing is put in backwards that half moon opening can hammer the balls to a short lived life and to a very fast failure(death). So beating on the bearing against its race can start the bearing on the way to failure too. Its pretty much the same failure too.
Handle bearings very carefully, don't unwrap them to look at them until your ready to install them so there kept clean, as clean as possible. You push in ball bearings y the outer race only. If you don't have the installing sleeve i use a large socket as the driver to press it into place. Please do not hammer on the inner race, again this will make galling marks in the inner and outer race and start the galling/fretting process and lead to premature bearing failure down the road.
Sometimes i can't believe what i see on the TV. At OCC they cut and grind on exhaust pipes and bike frames near the exhaust ports and weld splatter is near them too. When a four stroke engine cycles there is a short time when the exhaust port will suck or does an inhale before the intake cycle starts. It can inhale anything thats in the port(grindings/weld splatter) into the cylinders at this time so its very important what we do near and around the engines, mufflers, exhaust pipes and manifolds. Don't forget when grinding steel your grinding small steel particals plus the grinding wheel grit too. I cringe again when i see them doing this on the custom bikes. They would never make it in my world of machine building. There bikes are nice but there assembly process needs work.
When working on hydraulics keeping it squeeky clean is very important too. The biggest failures in hydarulics is dirt and over heating. Keep your assembly area clean when assemblying hydraulics and your hands too. You need to use lint free towels too. Lint/dirt can raise hell with hydraulic spool valves. Do it once and do it right.
Handle bearings very carefully, don't unwrap them to look at them until your ready to install them so there kept clean, as clean as possible. You push in ball bearings y the outer race only. If you don't have the installing sleeve i use a large socket as the driver to press it into place. Please do not hammer on the inner race, again this will make galling marks in the inner and outer race and start the galling/fretting process and lead to premature bearing failure down the road.
Sometimes i can't believe what i see on the TV. At OCC they cut and grind on exhaust pipes and bike frames near the exhaust ports and weld splatter is near them too. When a four stroke engine cycles there is a short time when the exhaust port will suck or does an inhale before the intake cycle starts. It can inhale anything thats in the port(grindings/weld splatter) into the cylinders at this time so its very important what we do near and around the engines, mufflers, exhaust pipes and manifolds. Don't forget when grinding steel your grinding small steel particals plus the grinding wheel grit too. I cringe again when i see them doing this on the custom bikes. They would never make it in my world of machine building. There bikes are nice but there assembly process needs work.
When working on hydraulics keeping it squeeky clean is very important too. The biggest failures in hydarulics is dirt and over heating. Keep your assembly area clean when assemblying hydraulics and your hands too. You need to use lint free towels too. Lint/dirt can raise hell with hydraulic spool valves. Do it once and do it right.