Cub Database Update (2019)

1955 cub with fast hitch that I have
Serial number. 188467
Engine serial number. L90182
Engine date code. 2 25 A

Original paint except the grill was replaced with a white grill
 
I would like to add my two Cubs to the database:

1947 Cub
Tractor has the coarse mesh grill and "McCormick-Deering Farmall Cub" decals (no circle decal)
Tractor Serial: 5727
Engine Serial: 5790
Engine Casting #: 6-20-Q
Engine Block Part #: 251341R1
Head Casting #: 8-29-Q
Bolster Casting #: 8-25-Q
Torque Tube Casting #: 9-9-Q
Transmission Part #: 351530R1
Transmission Casting #: 9-3-Q
Axle Extension Casting #: 3-1-Q
LH Final Drive Casting #: 8-14-Q
RH Final Drive Casting #: 8-14-Q
Hydraulic Block Part #: 354383R1
Hydraulic Block Casting #: 1-25-T
Interestingly, I found the original cover plate for the hydraulic pump hole in the toolbox when restoring!

1948 Cub
Tractor Serial: 42915
Engine Serial: 43422
Engine Casting #: 7-15-R
Engine Block Part #: 251341R1
Head Casting #: 7-27-R
Bolster Casting #: 9-2-R (it might be 8-2-R, the number is kind of worn)
Torque Tube Casting #: 8-5-R
Transmission Part #: 351530R1
Transmission Casting #: 5-26-R
Axle Extension Casting #: 8-7-Q
LH Final Drive Casting #: 8-2-R
RH Final Drive Casting #: 7-29-R
No hydraulics installed

As a side note, I remember years ago I submitted this information to another Cub registry on a different website. It had a nice form to fill out for submitting the information. I can't for the life of me remember what that site was called and cannot seem to find it anywhere on the internet so I'm assuming it is defunct. Does anyone remember this or know anything about it?

Thanks for maintaining this database, it's super interesting!
Ben
 
French Cub serial #703070, engine #193763, frame casting 11?-2-A (1952?), with C-22 sickle mower.
Albert Ploeg from the Netherlands.
 
Tractor YearTractor Serial NumberEngine Serial NumberNotesEng Casting #Eng Block Part #Cylinder Head Casting #Bolster Casting #Torque Tube Casting #Trans Part #Trans Casting #Axle Extn Casting #Left Final Casting #Right Final Casting #Touch Countrol Casting #Touch Control Part #
19498491985520 8-3-S251341R29-1-S..0889-R17-18-S351686-R17-18-S350798-R18-12-S8-15-S 351981-R1
Here are the numbers for my Cub. This Cub was in a flood and under water for a while. I'm slowly getting it dried out and cleaned up.
 
I would like to add my Cub to the database. Below are the numbers I have collected:

1957 Cub
Tractor Serial: Unknown
Engine Serial: FCUBM 219783

Engine Casting Date: 11/06/C
Engine Block Part #: 251341-R7

Head Casting Date: 04/17/C
Head Part # 251228-R1

Torque Tube Casting Date: 10/28/C
Torque Tube Part# 351686-R2 L2X

Transmission Casting Date: 10/03/C
Transmission Part #: 351530-R6

Differential Shaft Casting Date: 10/23/C
Differential Shaft Part# 350798-R2

LH Final Drive Casting Date: 11/04/C
LH Final Drive Part# 350806-R5

RH Final Drive Casting Date: 11/04/C
RH Final Drive Part # 350806-R5

Touch Control Casting Date: 8/22/C
Touch Control Part #: 360719-R1
 
I would also like to add my Cub to the database. Below are the numbers I have collected:

Location: the Netherlands (US aid Marshall Plan tractor)

1949 Cub
Tractor Serial: 94357
Engine Serial: FCUBM 95330

Engine Casting Date: 11-2-S
Engine Block Part#: 251341-R2

Head Casting Date: 10-25-S

Torque Tube Casting Date: 11-3-S
Torque Tube Part# 351686-R1

Transmission Casting Date: 11-2-S
Transmission Part#: 351530-R1

Differential Shaft Casting Date: 10-14-S
Differential Shaft Part# 350798-R1

LH Final Drive Casting Date: 11-1-S
LH Final Drive Part# 350806-R3

RH Final Drive Casting Date: 12-19-A
RH Final Drive Part# 350806-R5

Touch Control Casting Date: 10-14-S
Touch Control Part#: 354383-R1
 
1963 cub sn 221833J
Purchased from New Albany (Indiana)Truck and Tractor on 11/3/1963 for $1700.
New 42-C4 $150
Used plow $100
Used Disk $100
Used Cultivators $71
traded in a John Deere tractor, mower, plow, disc for $350 trade
Pop bought it from original owners in 1969 for $1200.
I have the original credit papers, but have misplaced the tractor bill. Iirc, deluxe seat was something like $25…
Tractor is not well traveled…less than 10 miles from original owner, and less than 25 from the plant. Have everything except the disc.
 
Anyone know what happened to the serial number/castings number chart? It says the page cannot be found......
 
Click on the HOME (top left corner, then information, then select from the dropdown list that appears. That might be what you're looking for. Also TM Tractor has a list on their webpage. Here's some info that I collected over time. Stan
 

Attachments

  • Casting code.JPG
    Casting code.JPG
    43.9 KB · Views: 8
  • CubProductionSN info.jpg
    CubProductionSN info.jpg
    147.6 KB · Views: 5
staninlowerAL said:
Click on the HOME (top left corner, then information, then select from the dropdown list that appears. That might be what you're looking for. Also TM Tractor has a list on their webpage. Here's some info that I collected over time. Stan
Click to expand...
I was looking for the chart someone was updating with owners input that showed their specific cubs with the options of listing casting codes on all the different parts. I was thinking it was the one that said 2015?
 
JimN said:
I was looking for the chart someone was updating with owners input that showed their specific cubs with the options of listing casting codes on all the different parts. I was thinking it was the one that said 2015?
Click to expand...
That might be Raymond Durban's database pdf file 2015 which has a lot more info about the part numbers/casting codes/different types & dates of changes etc. It's still buried in the forum in Barnyard's file somewhere as far as I know. Stan
EDIT: Go back to page 1 of this post and the link is posted in the first post on that page. Hope this helps. Stan
 
Last edited:
staninlowerAL said:
That might be Raymond Durban's database pdf file 2015 which has a lot more info about the part numbers/casting codes/different types & dates of changes etc. It's still buried in the forum in Barnyard's file somewhere as far as I know. Stan
EDIT: Go back to page 1 of this post and the link is posted in the first post on that page. Hope this helps. Stan
Click to expand...
Does that link work for you? It doesn’t for me.
 
You must log in or register to reply here.
Back
Top