Buying a new chainsaw?

BigBill

501 Club
I found out and learned many years ago about cutting down on my chainsaw cutting time.

I was asked to compete in the two local fairs with my husqvarna chainsaws by the local dealer. We took my husky 2100(6 Cu.In. 99cc's) and put a 16" bar and chain on it with a larger drive rim(like a sprocket).As i learned how they made the 8 cuts on a 9x9 timber my time speeded up. I did two cuts down, two cuts up, bored two holes without breaking of timber and then one cut up and one cut down. My best time was only 17.5 seconds. After seeing how fast these saws can really cut i took this gained knowledge into the woods with me. On a ten degree day (really cold) with this chainsaw I cut down a cord of wood, bucked up from standing timber in 50 minutes. Thats non stop cutting with no coffee breaks. I really relied on these bigger saws speeded up with the shorter bars for cutting fast.

After retiring from tree cutting a few years back I found myself with a $625 oil bill the last time the oil man came. I didn't spend that much all the last winter. I see the firewood prices going from $175 to $200 a cord to $250 a cord and its suppose to hit $300 by the fall.
Then my son was complaining about his electric bill in his new house. It was time to get the kid cutting again. We found a great place to cut at.
I'm just there for guidenance if he needs it. He started off years ago usin ga husqvarna 266 (66cc)chainsaw i had. Recently i let him use my new 575 (75cc)with a 20" bar. Rightaway
he got the hang of it. I could see the difference between the cutting speed of this saw compared to the larger saws i had years ago. Today i handed him a new 385(85cc) with a 28" bar with the skip tooth saw chain. Every other tooth is missing for chip clearance. It seems to still cut as quick as the regular saw chain but its quicker to sharpen the longer chain with less teeth. He found out what i been bragging about all these years that the bigger saws cut faster.

My point is if your going to purchase a new chainsaw and plan on cutting firewood I'd go for the bigger saw. For the beginner the 4 cu in saws are good for a starter saw too. The 575 is a great saw with a 18" or 20" bar. My little 353 husky is another good saw for limbing. For safety sake you have to match the saw to the job your doing too. A smaller saw with a 16" bar is perfect for limbing and smaller trees.

With the rising oil prices I'm looking back to the only renewable heating source we have "wood". I'd rather buy the kid new chainsaws than spend the $$ for oil. I think the oil suppliers are being very greedy now.
 
Great advice, Bill. :D :D

I have a Stihl 029 Farm Boss with a 20" bar that has severed me well for years. I also have a little Echo I use for trimming. A friend has several Husky's and just swears by them.
 
BigBill,

I couldn't agree more on the saw front. For years when I lived in the city, I fought with a cheap little Poulan that I'd had since the 70's...it was a great little saw for trimming branches and such...until I loaned it to someone...and it was trash after that.

After moving to the woods 4 years ago, I bought a Husky Rancher 455 with a 20" blade, since I'm never gonna tackle anything bigger than about 14 or 16 inches in diameter...and mostly 12 inches or less. I'm guessing it's only 45 cc.

This must have a smaller engine that what you're talking about...it runs flawlessly, but seems a little under-powered. But maybe I'm a wimp, because I'm not sure I want to work with anything heavier, and there's no way I'm gonna be cutting as fast as you pros! But do you think a 16 inch blade would perform better? Also, how long should a chain last with regular sharpening?

Thanks,

Corky
 
I have a Sthil 029 with a 16 inch bar , its a gerneral purpose do anything kind of saw originaly I had a 20 inch bar but it was too long the 16 is nicer for what I do sometimes I even wish it was a 14'' bar the Sthil is a good saw...
 
When i was into cutting firewood every winter(all winter long) from the fall to the spring I would go thru two 3/8" saw chains on my smaller saw, one 325 chain on my limbing saw and one 404 chain on my larger saw. How long they last is up to how many times you hit the dirt or rocks or metal in the wood too. If were lucky we hit nothing all season. I also sharpen my saw chain by hand with files. The power grinder for sharpening saw chain is only used when i would hit something and wreck the teeth then i had repair kits to replace the bad teeth with new teeth and the grind would make them all the same length faster than i could file them.

The local shops sharpen your chain with the grinder which also shortens the life of your chain very quickly too they grind off too much of the teeth. Your chain may last for two or three of the grinder sharpenings.

Another thing is what kind of saw chain your using matters too. In clean wood a chisel chain cuts faster. In wood with dirt in it you want a semi-chisel or chipper saw chain. Its more forgiving in wood with dirt in it. Chisel saw chain will lose its sharpness right away in wood with dirt in it but it cuts faster in clean wood.

I'm using more semi chisel/chipper type chain now with the wood on the ground because of the dirt in it. With standing timber i use chisel saw chain.

Its the right application for the type of saw chain you using too.
 
Sthil, Sthil, Sthil I wouldn't own anything else. I have had my Sthil for about 7 years (025) and it still cranks after 2 to 3 pulls. We have a local dealer that is excellent as far as service goes. If you have a good dealer for service and a good product your set :!:

Ron
 
I probably have one of the top husqvarna dealers in the northeast. When there is a saw that a dealer can't fix i seen it end at my dealer and he fixes it. I have fixed a few myself after they have been ridden hard by the loggers and even run over by the skidders too. XXit happens right? Bad days logging can be very costly sometimes between windshields and chainsaws.

I still like the larger power heads(engines) with the shorter bars they seem to just rip thru the wood very fast. With 100cc's and a 16" bar with 15" red oak its not even a challange.

BTW; "Firewood price update" As the nights are getting colder with labor day weekend just passing it didn't take too long to go from $220/$250 a cord to $280/$300 a cord already. Whats the price going to be when the first frost hits here? I just dropped $900 on one new 385xp husqvarana chainsaw and i ordered a 395xp already. I'm gearing up because of the cost of the firewood. I figure if we can put 20 to 30 cords of firewood away covered i have a good buffer for the years ahead. Its worth the cost of the new equipment to cut faster and get ahead.

What p!ssed me off was my oil man on his last visit was $625 for 130 gallons. I'd rather buy new equipment than pay for oil. I didn't spend $300 on oil all winter.
 
Forwarders are used a lot here now it saves the land and there's less dirt in the wood too.

Logging the old way with skidders can surely make a mess, well its up to the loggers too. When i was loggin i did fellin standing timber and was also used to clean up the loggers mess. I would cut up the tops left on the ground into firewood too. Sometimes we had limbs that were 24"+ too. I took all the work that was thrown at me.
 
Back
Top