Board Twist

Jeff Silvey

501 Club
I'm workin on a project for work. The board is yellow popular. It is 11" wide x 22" long.
I stained it then let it set for a week. When I got back to working on it it has a 3/8 twist from corner to corner. The board is not sealed.
How do I get this twist out?
Thanks
 
The only way I know of is to place it on a flat surface and put weight on it. It will take some time to flatten it.
 
Make sure that you wet both sides. A lot of times if they twist when you finish it's due to only finishing one side.
 
Not knowing the intended usage for the board. And if the previous suggestions do not permanently work. Basically start over. Cut the board into 4 pieces length wise. Turn every other piece upside down and end for end. Glue and clamp up.
 
Jeff, since the board had already acclimated to your shop I don't think there is much you can do. I would certainly try Eugene's suggestion. If you have a biscuit joiner I would use that also as you glue up the pieces. You may just have to get a new board. :(
 
I pulled a Poplar board out of a house a few years back that was over 16" wide and was well over 120 years old.
I then cut a section out for a marble game board and it warped like it was green lumber. The only way I could hold it was to glue another section onto the back warping the other direction. :roll: :lol:
 
Jeff:

From what I understand of yellow poplar it is also known as tulip-wood and is similar to our eastern white poplar and the willow family in characteristics. Tulip-wood has been used for well over 100 years as a fine stable material used most commonly as the case work structure for many fine period pieces of furniture made by some of North America's finest furniture makers. Tulip-wood is usually used in narrow pieces as it does have a tendency at times to twist although not as severe as some of it's close relatives. I like it a lot as it is a very easy wood to work with. Not local here though, we are slightly out of it's range.

Two suggestions.

1st would be to resaw it into 4 or 5 equal widths and then reglue using the alternating ring orientation rule. This will result in a rather stable board. Because tulip-wood has a very fine grain, as long as you glue up with the grain orientated properly the glue lines should be rather easy to disguise.

Tulip-wood takes stains easily and also absorbs moisture easily.... so 2nd would be to wet the board evenly -- mist it with a spray bottle and allow some of the water to soak in. Then clamp both ends with F- style clamps and a pair of cauls each end. The bottom caul should be perfectly square and flat. The upper caul should have a slight dished shape to it -- resembling a very shallow curved boat bottom for lack of a clearer analogy for the end that is twisted down. For the end that is twisted up then the caul should be kinda dished in, again not a lot. The difference should be less than 1/8" -- more closely to 1/16th than the 1/8. Clamp the cauls to the board very firmly and evenly alternating between ends which will force the board straight. Let sit for 48 hours or more if possible.

Can't guarantee that this will work and at best it may only stay stable for a while unless the finished board is to be encased in a frame. Even then the twisting (almost like memory foam for some woods) may reappear.

The best solution is solution #1.

Hope this helps.
 
Poplar is inexpensive. Why not just start over? That is a small piece.
Get a new piece that is close to quartersawn and it should not warp.

Putting weights on the board is unlikely to work unless it is wet or steamed. That may ruin your finish.

Ebony...I would try to save
Poplar...I would just make another.
 
Most wood has some internal tension, for a number of reasons, and any particular board may experience any or all of these reasons. Cutting the board in any direction upsets the previous balance. Applying finishing materials to just one side changes the rate at which moisture content changes on each side of the board.
If the back is not exposed, this link may offer some ideas. http://blog.woodshopnews.com/tbaw/?p=165
 
Back
Top