Big block 427 Chevy?

Jackman

501 Club
Any Chevy fans here? Whats the purpose of open chamber and closed chamber Big block 427 Chevy heads?

I have a pair of heads #3964291 hi performance vintage 1970 and I trying to understand what I specifically have :? ....
 
Closed chamber heads had high compression pistons(late 60's) this was life before the open chamber heads(70's) were available. The open chambers are large so they breathe better so they say. I believe all the stock factory horse power big blocks were all open chambered heads. Horse power is about flow too. I took a stock 1968 396cu 325hp ported the round port heads(small ports/closed chambers) and matched the intake and exhaust ports to the gaskets for the intake and headers for better smoother flow. I installed an upper intake oil baffle and an oil windage tray in the oil pan held by the extended main cap studs. I installed the 375hp/396 cam shaft, lifters and valve train/tripple springs. Using a stock cross jetted 780 holley on an elderbrock manifold. I installed the accell points set at .017", the cold plugs N5 champions set at .032" and the total advance on the timing at 50 degrees at 2,000 rpm. using the weight kit in the distributor and the vacumme advance too. On the full body dyno she had 299hp @ the rear wheels. I lost 100hp thru the drivetrain. Porting the heads lets it breathe better and tuning it exactly to what it needs to perform too. In a 1963 impala 4,050lb car in c/mp class with hayes fly/disc/pressure plate and a borg super t 10 4 speed with a 264 first gear and 4:88's in the rear she ran 12:85 seconds in the quarter mile on the second pass. I had to shift at 5,500 rpm because i forgot to turn the electric fuel pump on and it stilol ran 12:85. The 396/375hp cam redlined at 6,700rpm on the dyne max hp. So if the pump was on she should ran in the low 12's. I went thru the trapps at 3,500rpm so my 4:88's were too high i needed 5:13's or 5:38's then if all was correct the high 11's in the quarter was possible. But for the first time out i was happy. The borg super T10 was new and i had the second one in the state at the time. The total cost of the build was $2,500 to run in the 12.8's. The new $60k corvette's run these times now.

If you put the head gasket on the block you will notice a square corner at the top of the cylinder were the exhaust valve is in the head this blocks some of the exhaust flow. I rounded the square corner for a few extra HP too. Every trick adds up to HP.

Its not the size of the heads its how good you port them and where you port them. Remember closed chamber heads use closed chamber pistons, open chamber heads, open chamber pistons.
 
OOPs don't forget to remove the bronze bushing thats below the rotor in the distributor. It rides in a slot that limits the amount of movement of the advance the weight / spring kit gives to the total timing. I know with the vaccumne line attached on the distributor, The weights and the lightest springs installed from the weight/spring kit plus were we set the crank timing at will give the big block a 50 degree total timing at 2,000rpm. She comes on like gang busters at 2,000rpm.
 
I'm thinking those heads are off a 454....if the year is right. While not near as exciting as Bills car, I took the motor and transmission out of a totaled 70 Chevelle, (Some called it 70 1/2), and dropped it in my '67 Camaro. (Came stock with a 235 6 banger :lol: ) A run-of-the-mill 325hp/396 bolted to a Turbo 400 tranny. I had trouble with the weight in the front end, but a cut down set of truck coil springs solved that. Headers were added, and there wasn't a better sound around at the time. I switched out the Quadrajet for a Carter AFB. I'm not sure what it did to the horse power, if anything, but it pulled better on the lower rpm band. The Quadrajet seemed to nearly stall when first gassed......and I could never find a Holley that didn't flood the stock valve train. Traction/ Wheel hop was a big problem with the light reared Camaro. Traction bars helped a bit, but you had to be careful not to hang them on the turf if you ever left the pavement......for what ever reason. :lol: All in all, for me it was a low budget street rod that could make a lot of noise, melt the back tires, and get out of town in a hurry. I had a lot of fun with it. Most of the stuff I got was hand-me-down from a couple of cousins who were serious hot rodders in the late '60's. I learned a lot of mechanical ability tinkering with this and a couple other cars I had. Over all it was great fun. Gas was between 69 and 89 cents a gallon, nobody had any guns, we didn't drive through neighborhoods, and nobody got hurt. We had miles and miles of back roads to act up on. Brings back some fun memories. :lol:
 
Harold; You guys got me jones'n to grab a 70's 454/390 HP and to another build again. I would love to show my youngin's what fast cars are really like not the little fly by the seat of your pants japanese cars. You let the clutch up and sink in your seat from the G's when the M&H racemasters finally hook up. Its a feeling i'll never forget. My wife says i have enough on my plate right now. I found this 454 when i purchased my 396 back in 1970 and i heard its still there a few years back. A brand new 454 chevelle was side swiped and totalled it only had 800 miles on it. I know it will need a complete rebuild anyway but its the thunder i'm talking about.
 
Jackman":3auxyohu said:
Any Chevy fans here? Whats the purpose of open chamber and closed chamber Big block 427 Chevy heads?

I have a pair of heads #3964291 hi performance vintage 1970 and I trying to understand what I specifically have :? ....

Jack, it really doesn't matter. That 427 won't fit that H1, no matter how big of shoe horn you have!! :lol: Besides, you wouldn't want to put a slower motor in it anyhow!! :lol: :lol:
 
Hi all thanks for the replies I have been away from the site so that's why such a long delay....... I have three heads two Iron #3964291 and one aluminum #3946074 These heads aren't for me I bought them for 150 dollars at a yard sale and not being a Chevy guy I need to learn what I have to sell them at there true value, I am not a wheeler dealer flip it type but these heads are rare the iron come up as LS-6 and LS-7 they are old worn and need a complete rebuild but the 074 aluminum head dated 1970 is brand spanking new never installed a Gooogle search it comes up L-88 and ZL-1 and I am sure its worth some serious money. I had a Corvette collector /Vendor offer 300 dollars on the 074 he said thats a low whole sale offer on retail its a 1,200 dollar head but since he's a dealer he only buys at whole sale.
 
Back
Top