Anyone need beams, I joists for tractor barn projects??

CapeCodCubs

501 Club
Anyone up here in the northeast looking to build a tractor barn or ag barn?
I work for a truss fabrication plant and we have a lot of weathered beams and I joists. Some sets of trusses that customers didn't order right and if anyone has a need for these or has a project in mind let me know. These beams and I joists are in our yard for one of the county's biggest builders and they said throw them away. What a waste. So if you can pick up or want to look at and arrange a delivery by us you can have what you want.
Just doing some spring yard cleaning.

We are located in North Kingstown Rhode Island

http://www.trussus.com
 
Man, do I ever wish I was close enough to you... they would be gone in a heartbeat :!: :big say what: what a :censored: waste if they go in the trash heap... :big angry:

If anyone is close and needs trusses for a new barn.. goooooo gitem... :!: :!: :!:
 
I know it is a waste! They have 2 million dollars of product in our yard rotting away. We are a transfer station for 26 of their developments and all the sheet goods (plywood, etc.), 2 by's, Ijoists and beams get shipped out of here. I just took (2) 50' beams home, they are 7 inches wide by 18 inches deep. Our cost is $32 a foot. That's $3000 in wood going to the chipper who charges chip them up.

ScottyD'sDad I sent you a PM. Some good I joists here if you want to replace that roof in your main barn. Some good tongue and groove plywood with damaged tongues sitting around, too.
 
Dad and I are building a tractor barn just down the road from you on Bakerville Road. Plan to drop off the building plans tomorrow. What sizes are we talking about?
 
All differnt sizes of heavy beams and lots of misc I joists. Yeah you are right down the street from me. I live at the little farm on the corner of Lucy Little Road and Chase Road. Stop by sometime and maybe we can take a trip to see what we have here.

Chris
 
Hi Chris,

I'm definitely interested as well, the next couple of weekends are booked.

How long is mgmnt giving before they clear it all out.?

Thanks for thinking of us.

Joe
 
Hi Joe,

No management involved in this one. The builder that owned this stuff is out of Philadelphia, PA. There is no rush on our part, we have plenty of room. It was casually mentioned to me to ask my farmer friends if they wanted any of the beams that were being chucked out.
The thing is there have been a few guys interested in getting beams.
Cecil, Matt Smigelski, Jimdawg and ScottyD'sDad (Ed) have contacted me.
A few others have, too. Joe, what do you need?

Chris
 
New home contruction in this area has come to a screaching hault. The 84 Lumber plant that makes trusses for this area has closed. My father has a contractor's account at 84 and he placed an order for 5000sqft of drywall and they about fell over each other getting his order ready. He said he felt like royalty.
 
Tim,

Things are slower no doubt but we're busy enough. We did cut down from 70 guys to 54. Not bad considering the number of lumber yards and truss plants closing. We are non union so we picked up alot of work when some union places cut back and gave us their work. The good thing about this slow down is lumber prices are dropping. Like 5/8th inch tongue and groove roof sheathing is at $10.00 something a sheet. Not bad??? And service is alot better as your uncle knows.

CW
 
WOW! :shock: I live in North Kingstown and have been thing about a small barn for a cub. Let me know whats left. I worked at that Diesel repair shop down the road from trussco. On devil foot road, after I retired from the Navy for about 4 years. Not a nice place (Interstate Diesel that is, not Trussco) Scot
 
Chris:

It is a waste.. a sad waste. Ifn I was close, as I was saying to Cecil.. I know where a lot of that tongue and groove would go.. nice flooring for my shop and for my pole barn. 2 opposing layers of 5/8" on top of 2x6 or 2x8 at 12 inches or so and blocked every 12 or 16 inches would be a really nice floor for the pole barn. Would take the weight of the cubs too :!: Wooden floors are so much better on shot knees than concrete. Would make great underlayment for a roof, sheathing for a barn wall.. put a real savings into a new extension on a barn or out building for sure.

Hope you are able to salvage it all and save it from the chippers. Oh.. up here.. 5/8" tongue and groove is around $35 to $40 a sheet.. not the $10 down there.. so it is a very desireable commodity. The sign faces I got from my BIL run about $80.00 or so for 1/2 PT 4x10' sheets.. so the 86 I got saved me what..? about $6,880.00. I am only short about 20 sheets now to finish off the whole project.

I plan on getting some salvaged stock from my BIL hopefully this year. There may be a Bee-Hive that needs to be redone.. and the stock in it is still near perfect but if there is any rot at all, it has to be completely replaced. Missed one last year.
 
Rudi,

Lumber is crazy. This 5/8th T&G comes from a US mill on the Canadien border. Most of our lumber comes from Canada and I joists most of them come from Canadien mills. The southern mills are too expensive for us to buy from when you tack on shipping. Canadien wood products are better anyway. Hate too say it but the southern mills have too much inconstiency.
2 x12's vary in width by 1/2" of an inch. We have to run all it through a table saw to make it uniform in width. That is a waste!! Of time...
Do you ever get down to Cecil's? How far are you from Buffalo? Just curious, my parents have a summer place on Lake Erie. I'm out there in the summer. We used to have a big GMC box truck to run stuff out and bring back cheap hay @$1.00 a bale. They sold it.
I know what you mean about wooden floors, can't beat 'em. How about radiant heating under plywood??

CW
 
Scotlem,

I drive by Interstate Diesel everyday. Our shop has a few retired Navy here, too. Everyone retired in Rhode Island seems to be retired Navy!
The owner is a retired SeaBee Master Chief- Dick Duckworth. Should have applied here instead. Give me a call over here late in the day some time and I'll see what you might want. Trusses for a Cub shed would be about $10.00 each or so. New 10' wide with a roof pitch or you could cull out some I joists for a shed. 295-0669 work number.

CW
 
Chris:

It is so difficult to make any money in lumber these days that I don't even consider opening up my woodlot to commercial sales. Every 10 years I guess I do a nice pre-commercial cut thinning, which provides me with a thousand cords in pulp, and maybe about 10,000 bf of logs to sell. I harvest by hand pretty much.. a couple old tyme woodcutters take care of the heavy stuff for me and we pick and choose what trees we take down. All my firewood is usually pre-thin and dead stuff that may cause damage to younger or commercially viable trees. The yarding is done by horse team or with the Massey. I hope to use my Cubs in future thins.

The last time I sold wood, we only got about $6,000.00 out of it, but it is a help. It costs too much to have my wood sawn even with the mill next door.. but that is the way of the world I guess.

When I look at the amount of waste generated by mills lately, I cringe. They have no idea how much they are wasting and tossing away. When cutting timber there is a couple of Value Added products just waiting to be utilized.

1. Bark - used for mulch. Any species is great. Large stuff can be chipped into decorative mulch and the rest can be hilled and turned. In about 180 days much like a compost pile, you have this really great black fine mulch that is perfect for flower beds either private or municipal.

2. Sawdust - can be and should be required to be used as pellet stock before one single solitary tree is cut for a wood pellet plant. Also, good dry sawdust can be used for particle and flakeboard production. Oh, useful to in MDF production.

3. Mill Ends - these are very useful as they can be marketed as kindling for those who heat with wood furnaces. They can be used in OSB plants.. hogged up as large flakes and they can also be hogged up to be used in particle board plants as well.

4. Waste slabs can be used in a number of ways.. best scenario, stock is re-milled for truss and I-Beam production. Then the other waste goes into the above options.

5. As an eco friendly fuel for large plants. With Ash recovery programs (the ash can be used as additives to fertilizers as well as soil amendment products that are more green), the heat is used to heat the plants, as well as generate electricity and even the steam can be recovered in evaporators to produce water for recycling within the plant itself.

However, most mills have blinders on and their owners/operators do not see the value in expending money to get into this kind of game. If they only knew the value of having that Green Stamp plus the profit that can be gained from the Value Added products, they would jump at the chance one would think.

But.. that isn't going to happen. Maybe some legislation is needed?

Now, I haven't been to Buffalo in almost 30 years I guess. Ogden NY area would have been the closest to me when I lived in Ontario. I lived primarily in the North but then after joining the military spent time in Kingston and Ottawa.

We were at Cecil's last year.. for CubFest 2006. We will be there again in September or so is the plan.. and then off to do some rock hunting around Herkimer.. and points close by.

Hmmm radiant heat under a plywood floor? I guess. Never thought about it much. They have radiant heat in homes up here that have basements, so the main floor would have to be lined or something to handle the system. Probably would be a water based system in a wooden floor?? Don't really know, been a long time since I had to consider stuff like that.. way back in my college days.

Oh as for us Navy types, I am amazed at the number of ex-military who are into Cubs. I know a few of us spooks are here, and there are a couple from the Spec Forces and other branches too. BZ to the Navy Hands :!:
 
Back
Top