Anyone ever worked on Transfer case in Jeep

Miss Farmall

501 Club
I have a 1998 Jeep Grand Cherokee 4x4 which had a death whine coming from the Transfer Case. I say HAD since Ron placed it in 4 wheel drive and it will not disengage from 4 wheel drive back to 2 wheel drive. Someone said maybe a pin inside had dropped and is now in the way? We think perhaps the chain has become stretched and was causing the noise? Anyway, Ron is taking it apart as I type this and who knows what we will find...anyone ever opened one of these with this issue on a Jeep like this and what did you find? It is a 6 cylinder engine with a Dana 35 rear end and the transfer case is a 242. I found the chain online for a mere $110 compared to our local Jeep dealership for $290. Putting off ordering the chain until we get it open. Any suggestions a.k.a. guidance would be appreciated.
 
I only mess with the 1986 and earlier. After Chrysler took over they pretty much went in a different direction. The CJ and Full size Wagoneer/Cherokee was the last of the good Jeeps. I never had a TC apart.

Go to this site http://www.jeepsunlimited.com/forums/. These guys are probably one of the last Jeep forums that will give you a straight answer without flaming the tar outta you. I think John Strenk is the "Big Dog" on that site. They should be able to help.
 
just thought I would check in, will give the sight a try. We are going for the band aids now, after an ice pack earlier, poor Ron. Trying to get pin out of drive shaft to remove t. case.................would not be a good shade tree mechanic without some blood huh?
 
Sounds like you got some good leads for some advice.

I used to have the old military jeeps and am pretty familiar with them but the modern stuff is much harder to work on. I've not had a TC apart in quite a few years.
 
The newer t-cases are alot different than the old ones. This model holds about a quart of dexron ATF as lube oil, it has an oil pump, suction tube and pressure lubed bearings and upper main shaft. All the bearings have lube holes to line up along with a certain position for the oil pump suction screen. Also there are bearings and etc that need to be pressed out of the main shaft and case also. The oil pump is needed because the upper main shaft is running above the lube and without the front axle turning no lube is carried up to the main shaft this is also where the shift linkage slides the 2/4wheel drive and high/low range gears on the shaft. My guess is that you had a lube failure and starved the mainshaft bearings that caused the noise along with the shifting problems. This unit has multiple things that are replaced as a assembly. These units also have a Technical Service Bullitin on an upgrade on the shift shaft assemblies that can cause a grinding or thumping noise. For futher help I would check with a local 4 wheel drive shop, there are a lot of these units out there.
Hoping this helps
Mark
 
no comment from me. hubby reads this forum :||): <<<<this would be he and I. I would be the recipient of the squeeze only his little yellow hands would be lower, as in around my neck! :lol: Bless his heart. He removed the entire case and is taking it to a friend to open. Still a mystery............. :?:
 
Stacey,
Tell Ron to give Charles a call he might be able to help. Like it was said Barnyard and him are up on all this jeep stuff.

Ron
 
I work on Chevy’s and Fords, but I do have friend who works on Jeeps. I’ve done a couple of NP transfer cases myself and the most part you can repair them. Just take your time.

A friend downloaded a section from the Chrysler service manual on the 242 NP transfer case for R&R and overhaul procedure. I have put in a PDF file and sending it to you as an attachment through personal e-mail. It’s a little on the large side, hope you can download it. The Chrysler service manual is different than the other auto manufactures on the way you read them. Chrysler service manual describes the service procedure, than you have to click on a link to open a picture, so all the pictures (in the most part) are after the entire description in the file I’m sending you. I hope it helps and if can help you more… “drop me a line”.

Jack
 
I just tried to send the e-mail and your email provider sent me a message that stated the attachment was too large. If I can resend another way, I’ll let you know.

Sorry,

Jack
 
Hey Ron and Stacey,

Sorry you're having t-case troubles on the jeep. I did a google on New Process 242 (the brand and model you have), and came up with this:

"One common operating problem with the 242 transfer case is that it will stick in 4wd even if the lever is moved to 2wd. Internally, moving the lever loads a spring which then applies force to move the selector fork. If the gears are loaded with torque, the spring will not have enough energy to move the sleeve off the gears. Once torque is removed from the gears, the spring will then move the fork and slide the sleeve of the gears.

Momentarily lifting your foot off the gas will often unload the gears enough to allow the spring pressure to move the fork. On some high mileage units, a wear groove will form on the sleeve or gear causing it to stick longer and may require a couple of changes from loaded to unloaded to get the sleeve to release form the gear."

This sounds like it could be your problem, but this is just a guess. Here's the link: http://ezinearticles.com/?Jeep-Select-T ... &id=281045 And a link for rebuild kits: http://www.drivetrain.com/transfercases ... odel%20242

I've never cracked one of these puppies, and I'm having some issues myself with my 88 Wag that has a old NP 208 swapped in. A Jeep buddy of mine told me that I couldn't go wrong getting in touch with Steve Runyan at STR Transmissions in Woodstock....look him up and give him a call. Ron, since you've already got it pulled out, you can take it to STR and they'll rebuild it on the bench I'm told. At least that's my plan...I'm not smart enough (or brave enough! :o) to bust into something with so many gears! :D

Let us know how it goes!

Corky
 
wow the memories the idea of that brought back. i never went inside of the transfer ,but i remember back about 20-25 yrs ago when i was running a 1967 jeep with the 327 vigilante engine. around march of that year, of course when it was cold as a witches :censored: . the rear freeze plugs blew. i remember laying out there on that cold ground pulling the drive shaft, of course after jacking up. then the transfer case and the transmission . lord knows i almost froze out there. we were young and starting out.money was a serious issue. yup when the going gets rough the tough gets going. 8)
 
Back
Top