Ferguson TO-30 hydraulics

offrink

Well-known member
I rebuilt my pump on my Ferguson due to it being slow to lift and a little jerky. When I refilled it I refilled with regular generic hytrans. Pump works fine but was a little slow and upon further reading I learned it’s not the proper fluid for the system. So I dumped it and replaced the fluid with 15w-40 oil as I read it was a good substitute. Now the 3 point lift from bottom to top in about 5 minutes! Being it’s winter in Michigan and I use it to move snow occasionally, this just won’t work. What kind of options do I have and what should I be checking.
 
Did a quick search and everything I see recommends 90w GL-1 oil. Tractor Supply sells it labeled as Ford Transmission Oil. Make sure you bleed any residual air and let the system warm up before you do a timed test.
 
Last edited:
Did a quick search and everything I see recommends 90w GL-1 oil. Tractor Supply sells it labeled as Ford Transmission Oil. Make sure you bleed any residual air and let the system warm up before you do a timed test.
I do see that too and swapping every winter (or temps below 50*f) to 80 weight. I also see that in Europe they use 15w-30 in their fergusons as well as fords. Because I’m in Michigan with temp swings from -20*f to 110*f my thought was to go the European route and not have to change fluid seasonally. It also would seem like after 30 minutes of running and 2 miles of driving in theirs and fourth and 10 cycles of the pump it would quicker but it doesn’t.
 
is that the big heavy pump that goes in the transmission ? had one did same on a MF 202, even after rebuild, ended up buying a new pump on ebay, at the time it was not big $$ , couple hundred bucks, put it in and it worked just fine
 
is that the big heavy pump that goes in the transmission ? had one did same on a MF 202, even after rebuild, ended up buying a new pump on ebay, at the time it was not big $$ , couple hundred bucks, put it in and it worked just fine
Yes. It does share the same fluid and sump.
 
Did you replace the o rings on the standpipe that goes between the pump and the plate on top of the transmission housing ? They can dry out and crack then leak back to the sump.
 
I got a rebuild kit from Steiners. So if it was in the kit I replaced it.
Edit: actually yes I had to order them from an outside source. I think I bought 100 of them.
 
Last edited:
I do see that too and swapping every winter (or temps below 50*f) to 80 weight. I also see that in Europe they use 15w-30 in their fergusons as well as fords. Because I’m in Michigan with temp swings from -20*f to 110*f my thought was to go the European route and not have to change fluid seasonally. It also would seem like after 30 minutes of running and 2 miles of driving in theirs and fourth and 10 cycles of the pump it would quicker but it doesn’t.
I saw the 80w comment, too. But, I think you might be hard pressed to find a straight 80 weight GL-1.
 
It might be that I just table this for warmer weather. I will have to find another piece of equipment to use.
 
So then hytrans fluid should work just fine and not have any long term damage to any components? The interwebs don’t seem to have a good answer.
 
So then hytrans fluid should work just fine and not have any long term damage to any components?
No damage. The only down side I can see to Hy-Tran equivalent in the TO-30 is any effect you might get from the wrong viscosity. Hy-Tran is quite thin -- I think roughly the same as SAE 10. As I read your original post, your speed problem got worse when you changed from Hy-Tran to 15W40. I would expect that.

Back in my youth, we had a TE-20 with a snow plow. It had the original type SAE 90 oil, or something similar. The snow plow was slow, usually started to work well about the time we finished using it. We were given the suggestion to change to a thinner oil by replacing the gear oil with hydraulic oil (early versions of Hy-Tran were available at the time). We never did try it.
 
No damage. The only down side I can see to Hy-Tran equivalent in the TO-30 is any effect you might get from the wrong viscosity. Hy-Tran is quite thin -- I think roughly the same as SAE 10. As I read your original post, your speed problem got worse when you changed from Hy-Tran to 15W40. I would expect that.

Back in my youth, we had a TE-20 with a snow plow. It had the original type SAE 90 oil, or something similar. The snow plow was slow, usually started to work well about the time we finished using it. We were given the suggestion to change to a thinner oil by replacing the gear oil with hydraulic oil (early versions of Hy-Tran were available at the time). We never did try it.
Late last week the temp was 52* and I decided to start the tractor up and see how things go. They hydraulics were still nearly fully raised position after almost a week. The hydraulics cycled much quicker. A full up and down cycle in maybe 10 seconds. As it sat running it did speed up slightly. Maybe 8 seconds by the end of a half an hour. So either I had possibly air in the system or something else wrong or just that the 10* different made a huge difference. I’m not sure. When I have time I’ll try it again and see how things are going. Been to busy lately hunting and potato digging.
 
Maybe a magnetic block heater attached to the rear end might help get things moving quicker this winter....
If you don't have an inside/heated area for storage, if you could help capture any heat by covering things with a tarp or some other "windbreaker". Same principal as is used to start a diesel engine in the winter by heating the oil pan to thin the thick oil so the engine is easier to turn over. JMHO Stan
 
Ha! I did almost the exact same thing on an old Ford tractor I had. Figured 'oil is oil' and put in something I had on the shelf. The hydraulics slowed to a crawl, just like yours.
Turned out those old girls are super picky. I switched over to 90w GL-1, and it was like a brand new machine. I'd bet a donut that's your issue, too.
Let us know if that does the trick!
 
Ha! I did almost the exact same thing on an old Ford tractor I had. Figured 'oil is oil' and put in something I had on the shelf. The hydraulics slowed to a crawl, just like yours.
Turned out those old girls are super picky. I switched over to 90w GL-1, and it was like a brand new machine. I'd bet a donut that's your issue, too.
Let us know if that does the trick!
It definitely could be the issue. I just hate the idea of switching it over every 6 months.
 
Back
Top