ALlis Chalmers B stuck engine

Joey

501 Club
I acquired an AC B a couple of years ago and parked it in my barn to wait for its redo in my retirement. The engine was free, I could turn it with the hand crank. Now, the engine won’t turn with the crank. I removed the plugs and sprayed a whole can of PB Blaster in the holes, followed by a can of Kroil in all the plug holes. I removed the starter to access the flywheel but I can’t get any leverage to try and move the flywheel with a crowbar. I jacked up the right rear tire, put it in 3rd gear and rocked the tire back and forth for about a week... started seeing movement of the flywheel. Now, I can move the tire around, sluggishly, but the flywheel doesn’t move. My question...how can the wheel turn while in gear, but not the flywheel?
 
Your tractor has a differential so one wheel can turn independent from the other. You may want to put both wheels back on the ground and try rocking it back and forth while in 3rd gear to see if you can free it up. Don't try pulling it in gear to turn it over because you could possibly cause damage.
Have you pulled the valve cover off to verify that all of the valves are free and not stuck?
 
If you have a large 15" or 24" flat jaw adjustable wrench, you could engage the PTO with transmission in neutral and try and turn it that way. Depending on your resources and what you have to work with, you could also take an old female PTO stub yoke, and weld a socket to it, slip it on the PTO shaft and use a breaker bar to turn it. A piece of pipe will give you a bit more leverage.
 
Thanks Ricky for the info, the tractor is back on the ground and rocking…I’ll pull the valve cover today and peek inside.

DJ, if the engine is not freed, I have a welder friend who may be able to fabricate the PTO stub yoke…that’s an interesting idea.
 
Keep in mind that with the gearing of the PTO, it will take 2 or 3 times the force at the PTO to put the same force on the crankshaft as you would get from a crank directly on the engine. It isn't like a Cub.
 
I'm thinking the complete opposite. The gear on the main shaft to engage the smaller gear on the actual PTO shaft is approx. 2.5 times bigger, and engine speed is reduced from approx. 1700 rpm's to 650 rpm's on the PTO shaft. So powering back through the PTO shaft should give you an approx. 2.5 gear reduction advantage. Whereas, the Cub is a 1:1 ratio engine to PTO.

I use this method after splitting a tractor for clutch replacement, etc. Engage PTO and put a wrench on the PTO shaft to move it back together, putting it in first gear. Once the input shaft meets the clutch plate, put it in neutral, so as to "feel" the splines to align turning the PTO shaft. Once engaged I'll roll and jiggle it together and have longer bolts in the bell housing and engine block to chase it up, not to pull it together. Once the input shaft is through the clutch disc, I'll put a wrench of something similar on the clutch release lever to relieve any misaligned pressure on the input shaft so it can go into the pilot bearing/bushing. 99 times out of 100, it will go in like it has eyes.
 
Last edited:
I'm thinking the complete opposite. The gear on the main shaft to engage the smaller gear on the actual PTO shaft . . .
And that is where you are going wrong. The gear on the PTO shaft has to be bigger to slow it down to normal PTO speed.
 
With only one tire off the ground and the tire rotates while in gear, but not the engine, the clutch must be slipping. Is the clutch pedal stuck part way down?
Dennis
 
And that is where you are going wrong. The gear on the PTO shaft has to be bigger to slow it down to normal PTO speed.
I stand corrected, you are right. Don't know what I was thinking. Still a good chance it will work though. One way to find out..!!
 
Well guys, I didn’t have to put the wrench on the pto. With the tractor on the ground, I rocked it a couple of days and saw a little movement of the flywheel. I used a small crowbar through the starter hole and finally got the flywheel to move. I removed the valve cover and verified no valves were stuck.
With the engine in neutral, I used the hand crank and finally got the motor to spin. As I cranked it faster, a little debris flew out of the starter hole and it looked like pieces of a mud dauber nest. I sprayed more lubricant in the spark plug holes and around the valves and continued cranking. She now spins freely.

Thank you guys for all the suggestions and help, even though it’s an Allis Chalmers! It’s a learning experience and definitely different from a Cub!
 
Sounds like another one on the way to being saved. Congrats on your success. An AC B was my first tractor to drive (about 75 years ago) and first to rehabilitate about 20 years ago. Stan
 

Attachments

  • DCP_0003.JPG
    DCP_0003.JPG
    114.7 KB · Views: 7
Back
Top