Wagner WM1 loader mounting brackets

The Cub Club -- Questions and answers to all of your Cub related issues.
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
MrBee
Posts: 23
Joined: Sat Jun 30, 2018 11:01 pm
Zip Code: 08221

Wagner WM1 loader mounting brackets

Postby MrBee » Sun Nov 08, 2020 11:37 pm

I just picked up a Wagner model WM1 loader, and it is missing the front mounting brackets. Does anyone happen to have good pictures showing how one mounts to a cub? I believe the rear of the loader attaches to the final drives, and the front appears to use the square tool mounts on the front bolster. I have attached a picture showing what I need. I’m thinking it should not be too hard to fabricate the missing parts.

Matt


914A78D2-31ED-4A45-8662-DEA7F72285CA.jpeg

Crimson Tim
5+ Years
5+ Years
Posts: 572
Joined: Wed Feb 19, 2014 1:09 pm
Zip Code: 32736
Tractors Owned: The crew:
"John", 1952 Cub
"Paul", 1951 Cub
"George", 1958 LoBoy Cub with Wagner 45 Loader
"Ringo", 1977 Cub

So far, Paul and Ringo have arrived. John and George were supposed to follow ages ago, but apparently have gone awol. Long story.
Circle of Safety: Y

Re: Wagner WM1 loader mounting brackets

Postby Crimson Tim » Mon Nov 09, 2020 11:49 am

Pm sent.
I am in the same boat, and have compiled a bit of information.
First, make sure which version you have. There were three different versions, I believe, and different mounts for standard Cub versus Loboy.
I believe that page you posted shows the standard Cub. Is that what you are mounting on, and is that what your loader was mounted on before?

PM me an email address, and I will forward the information that I have accumulated.

User avatar
Barnyard
Team Cub
Team Cub
Posts: 23468
Joined: Tue Aug 07, 2007 3:39 pm
Zip Code: 45030
Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100
Circle of Safety: Y
Location: OH, New Haven (Hamilton County)

Re: Wagner WM1 loader mounting brackets

Postby Barnyard » Mon Nov 09, 2020 12:37 pm

Check out this thread I started a couple of years ago. viewtopic.php?f=1&t=102770
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.

Circle of Safety

MrBee
Posts: 23
Joined: Sat Jun 30, 2018 11:01 pm
Zip Code: 08221

Re: Wagner WM1 loader mounting brackets

Postby MrBee » Tue Nov 10, 2020 10:17 am

Thank you for the responses. The back mounts make sense, as they just attach to the final drives. But I’m not seeing how the front brackets work. Is the whole front of the loader assembly supported by the square bar going through the steering bolster, or is it also supported on the axle somehow. Seems to be a lot of weight in that one spot.

Matt

User avatar
John *.?-!.* cub owner
Team Cub Guide
Team Cub Guide
Posts: 23684
Joined: Sun Feb 02, 2003 2:09 pm
Zip Code: 63664
Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
Location: Mo, Potosi

Re: Wagner WM1 loader mounting brackets

Postby John *.?-!.* cub owner » Tue Nov 10, 2020 12:44 pm

ON the front of your loader does it have a plate that extends down with 2 holes in it, or does it extend down just a little with a plate turned flat going crosswise with 2 holes in it? A picture of the front would be helpful.
If you are not part of the solution,
you are part of the problem!!!

MrBee
Posts: 23
Joined: Sat Jun 30, 2018 11:01 pm
Zip Code: 08221

Re: Wagner WM1 loader mounting brackets

Postby MrBee » Fri Nov 13, 2020 11:20 pm

Here is a picture of the front. It is just a plate that drops down about 2 inches.
E1312329-A3BD-4D89-9B3C-5F35C6BE4D57.jpeg


Matt

User avatar
John *.?-!.* cub owner
Team Cub Guide
Team Cub Guide
Posts: 23684
Joined: Sun Feb 02, 2003 2:09 pm
Zip Code: 63664
Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
Location: Mo, Potosi

Re: Wagner WM1 loader mounting brackets

Postby John *.?-!.* cub owner » Sat Nov 14, 2020 6:30 pm

That one was the later version of the WM-1. It would mount on a standard cub or a low boy, just used different hardware. I have picturs of the one that worked on a standard cub only, but not that one.
If you are not part of the solution,
you are part of the problem!!!

MrBee
Posts: 23
Joined: Sat Jun 30, 2018 11:01 pm
Zip Code: 08221

Re: Wagner WM1 loader mounting brackets

Postby MrBee » Mon Nov 16, 2020 3:24 pm

John,

Can you post pics of the front mounting brackets on the one you have? I’m putting mine on a regular cub. Thank you.

Matt

Pa67farmerMike
5+ Years
5+ Years
Posts: 5
Joined: Sun Nov 02, 2014 8:35 am
Zip Code: 16423

Re: Wagner WM1 loader mounting brackets

Postby Pa67farmerMike » Sat Nov 21, 2020 7:01 pm

Front mount for loader
Attachments
5A054246-C129-4385-8E0A-2E2995C53B7B.jpeg
Front mount for loader

MrBee
Posts: 23
Joined: Sat Jun 30, 2018 11:01 pm
Zip Code: 08221

Re: Wagner WM1 loader mounting brackets

Postby MrBee » Sun Nov 22, 2020 4:11 pm

Thank you for that picture. That is exactly what I am looking for. Wouldn’t happen to be for sale, would it?

Matt

Pa67farmerMike
5+ Years
5+ Years
Posts: 5
Joined: Sun Nov 02, 2014 8:35 am
Zip Code: 16423

Re: Wagner WM1 loader mounting brackets

Postby Pa67farmerMike » Thu Nov 26, 2020 5:07 pm

Sorry, not for sale. Need it for my loader.


  • Similar Topics
    Replies
    Views
    Last post

Return to “Farmall Cub”

Who is online

Users browsing this forum: No registered users and 4 guests