Transmission noise

The Cub Club -- Questions and answers to all of your Cub related issues.
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Iamaxxer
Posts: 10
Joined: Thu Aug 01, 2019 7:55 am
Zip Code: 50677

Re: Transmission noise

Postby Iamaxxer » Sat Feb 01, 2020 12:24 pm

Urbish wrote:Have you jacked it up and turned the rear wheels by hand with the tractor in neutral? You might have something bad going on in the final drives, or at the ring gear in the differential. Differential is easy to inspect. Or maybe you have a smoked bearing. Did you check all bearings when you had it apart?

If the issues was differential or final drives,wheel issues the noise would be in all gears correct?

User avatar
Barnyard
Team Cub
Team Cub
Posts: 23496
Joined: Tue Aug 07, 2007 3:39 pm
Zip Code: 45030
Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100
Circle of Safety: Y
Location: OH, New Haven (Hamilton County)

Re: Transmission noise

Postby Barnyard » Sat Feb 01, 2020 1:38 pm

The noise I hear in yours sounds like one mine is doing. Not sure what it is but it is getting a different trans at DSCF this year.

There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.

Circle of Safety

User avatar
Lt.Mike
10+ Years
10+ Years
Posts: 2432
Joined: Sun Feb 17, 2008 2:38 am
Zip Code: 07727
Tractors Owned: 1 -'58 International Cub Lo-Boy
2 - '46 International A's
2 - '52 Farmall Cubs
1 - '53 Farmall Super A
1 - ‘41 Ford 9N with a ‘49 8N Engine
1 - ‘48 (5641) Allis Chalmers G
Location: Farmingdale NJ

Re: Transmission noise

Postby Lt.Mike » Sat Feb 01, 2020 5:09 pm

Iamaxxer wrote:Ok, tore the transmission open... found a welded up 1st / reverse shift fork. And broken teeth from a previous repair in the bottom of the rear end. No missing teeth on any of the present gears.
Spilt the tractor to replace the shifter fork and rail, and replace the bearings and seals on the top shaft..
Noise is still predominantly 1st and 2nd...3rd runs very smooth..
Lower shaft?

It was suggested to me that the noise in mine was from the forks being misaligned or worn.
You’ve said yours was weld repaired.
Perhaps it looks right but is off just a hair causing this problem. Can you get your hands on another cub to borrow the shifter an forks from?
Install a known to be good set and see what happens. If it runs quiet it’ll save you a lot of work.
Quote by Gary Pickeral I like
"If it can cast a shadow, it can be restored"

Iamaxxer
Posts: 10
Joined: Thu Aug 01, 2019 7:55 am
Zip Code: 50677

Re: Transmission noise

Postby Iamaxxer » Sat Feb 01, 2020 5:17 pm

A Used shift fork and rail were purchased and installed..


  • Similar Topics
    Replies
    Views
    Last post

Return to “Farmall Cub”

Who is online

Users browsing this forum: Cubfriend and 2 guests