Underground Pipe Locator

lyle11

501 Club
Has anyone ever used a pipe locator device to locate an buried PVC pipe? Figured if the rental place has one I’d try it but was curious if anybody had any experience, good or bad, with one before I try it. I expect the end of the pipe is within a foot of the surface. I heard dowsing might work too with water running down the pipe but I’ve never had any success with it.

After I call Diggers hotline and get gas, electric, etc marked, I want to find the end of the pipe(s) because they can’t accommodate a heavy rain. I did find the end of one pipe by running a hose down a gutter but that is on one side of the house. I expect to find at least one pipe on the other side. Hoping to minimize the digging as I search for the pipe. On many houses on my street the pipes are visible and drain into a shallow ditch. Based on the pipe I located, they filled in the ditch and buried the open end of the pipe. I either have a collapse between the pipe and the house or, there is too much resistance at the end of the pipe to soak up the water. It drains in an hour or 2. I figure if I can locate the end of the pipes I can at least see if they are restricted.

Thanks
 
I think you are going to have to have something metal in the PVC pipe to connect the signal generator to so the receiver can detect it. That's typically what the locator guys are doing. Maybe if you're nice to them when they come to find the others and already have a fish tape or electric wire stuffed down your PVC pipe maybe they'll hook onto it and find the pipe for you. You may be in an area where they send one guy to mark everything. He may be more interested in finding where your pipe goes first then marking the other utilities that are near it than marking you whole yard.
 
Run a sewer snake down the line. It will tell you how far it is to the point it is plugged and provide metal for the locater.
 
I use a tile probe here.---If pipe is only a foot or two deep, it would be a piece of cake to find without going to all that trouble with locators ! Probe won't tear up yard, in fact the holes would be good for getting air down to the roots! ---As a side note,--- the fewer people you have messing around, the better! ----- just in case--------! thanks; sonny
 
Thanks. Good information. I’m in the early stages. All I know is that the sump pump exits the house with a 1 1/2” pipe that drains the water into the exposed open end of a 4” buried pipe. Works fine, until heavy rain, then the 4” pipe (which I assume is connected in the ground to downspout pipes) backs up and the sump pump water ends up on the ground right outside the foundation. An hour or two later and the water has receded from the 4” pipe. So, it’s restricted somewhere.

Once the yard is marked and it’s okay to dig, I should be able to find the pipe in the mulched area by the house and have a pretty good general idea where it runs so I can use some of your ideas to find the end near the street.
 
Eugene":esieihqf said:
Have you tried to probe for the pipe?
I did this a couple of weeks ago.
I had a pvc pipe exposed at the top of the hill above the river behind my house. I had some concern what it was hooked to and it’s purpose by the PO. I used a length of rebar pushing into the soil. It makes a distinctive scrape noise when it hits pvc. You can pretty much predict the direction it’s running after a few feet.
I was worried the PO had hooked it up to the old septic field but found it ran some 300’ back to the house where it was once hooked as a clothes washer drain.
 
Take a coat hanger and cut a piece about 18 inches long then bend in a L shape. Hold the short leg loosely in your hand with the long leg pointing straight out away from you. Walk slowly in the area where you think the pipe might be and when you cross the pipe the coat hanger will move in your hand and line up parallel with the pipe. I was shown this by an old septic repair guy. I can’t explain how it works but it does. Try it over any kind of pipe or wire buried under the ground where you know how it runs and you can see how well it works
 
That’s exactly what the utility marker guy did. He used 2 of the wire rods from the marking flags with the flag removed. They are about 18” long and he bent them at a 90 degree angle about 1” from the end. He held one loosely in each hand in front of him crossed and parallel to the ground. When he got over the buried gas line, which was already marked and they told me is made of plastic, the wires pivoted outward making a straight line over the gas line. They called it a witching rod. I never looked it up to see an explanation of how it’s supposed to work.

He repeated the process and told me where he thinks the drain pipe is located. I dug about a foot down in 3 places along the line he marked but found nothing. It might be buried deeper.

So I dug down deeper and exposed a foot of the pipe where it originates by the house and the pipe was thin walled and distorted to a compressed oval shape. If I run a water hose in a downspout, in about 20-30 minutes water appears by pipe I exposed, so I’m sure it’s cracked and compressed but open enough to take a slow flow of water away but not a big rain. But now I have no need to find the end where it drains. I hired a guy to install a new pipe of heavier PVC and drain it into a culvert.
 
Be sure to call your state locating service to get everything in the area marked. By law in some states excavators cannot dig unless that has been done. nDo that even if you are sure there is nothing there.
 
I had a new underground pipe run yesterday. The pipe location identified by the utility guy with the witching rod was wrong. There was no pipe located there. However, the witching rod identified the location of the gas line and, it ends up the old drain pipe was inches from the gas line. So he was half right. I kind of suspected the pipe was located by the gas line based on the shortest and most direct path to the street, but I wasn’t gonna take a chance digging there.
 
Back
Top