It’s early Wednesday morning and getting ready to get on a flight to Detroit. I’m setting here looking at my Laptop of notes for two days of classes I have to give. I was doing a little research on the web and I drifted over to Farmall.com. (You can see where my mind is). I’m going to copy and paste a post into Word and write my reply when in flight. Maybe the Flight Attendants will think I’m some sort of a big shot when I’m typing away, but on second thought if you could see me type it will be the contrary.
I’m in flight and there is one thing I just found out never to do with this laptop; never copy and paste any of the Farmall.com forums to Word because I just about crash this thing for some crazy reason. I ended up pasting everything to Word pad and that worked somewhat better. I do this on my Desk top PC (to Word) all the time and I have no problems. This really scared me; all my info for the next two days is on this thing!!!
My flight is Via Cincinnati to Detroit and I hope I can get a Wi- Fi hot spot to post at the Airport.
My vacuum system vents back into the 1200+ sq ft shop through a filter system and I have an auxiliary circulating filter to use when the woodworking equipment is in operation. By doing it this way, I don't lose (note spelling) any heat.
I don't have ANY bare wall. In addition to the overhead door I have 3 walk in doors with large windows in them that don't waste wall space.
My ventilation system exhaust into the unheated garage where the Dodge truck is setting. (1000 sq.ft) The wood shop is a closed four wall, ten foot ceiling all insulated. In the garage area where the truck (Dodge) sets, I have future plans of finishing and insulating. Two major things that are in my way at this time, which are….. time and mostly money. I use this garage area for painting and light repair when weather permits.
The vent out of the wood working shop was an experiment to see how much fumes entered the other garage area through the filter. I didn’t want to loose any heat like (George has his set up). I have a filter on the exhaust much like an auto paint shop has, but when you’re using any solvents (varish, stain, ect.) in the wood shop it gets pretty fumy in the area where the exhaust comes out, at which time all the heat is pulled out of the wood shop. With electric base board heat there is no quick recovery. I forgot to say I do have a vent for outside fresh air in the shop and that’s were I was talking about a heat exchanger. When I insulate the area where the vent comes out of the wood shop I don’t think it will be too safe with those fumes coming out like they do.
Do you have this issue George? The only thing left, is vent to the outside and then I’m defeating the heat issue. The way I can fix this is a quick recovery heat system, but that will cost a lot of dollars for heat. The exhaust for the equipment saw dust is piped through the floor to the outside and I have a minimum heat lost with that.
The shop where the Ford truck sets is 900 sq.feet. + 500 sq.ft.of Storage. This is a clear span truss building with 16 foot (at peak) ceiling with 10 foot walls. I have it insulated trying to find the time to build the partition between the shop and the storage space. I built this type of building (clear span truss type) so I can someday install an auto lift and also pull large equipment in to work on. Entrances to this building are an overhead door, walk in and a double siding for the storage area. If you can notice in the picture a Backhoe is setting in back part of the building.
When I built these buildings, heating them, was very much on my mind. I use Propane to heat my house so I ran an extra gas line to a place where I thought I may put the furnace. Then I started thinking about the possibility of explosions and fire with the furnace inside the buildings, especially when painting, fuel spills, fumes and ect. So I dropped that idea and put electric base board heaters in the wood shop and now trying to decide what to do with the rest.
I think I read of someone talking about a ground source heat pump. When I built my house I almost went that route. The cost was $10,000 at the time and I couldn’t justify it, but they said it would pay itself back in ten years. I installed a 90+ gas furnace which really runs very efficient, but I paid $1.25 a gallon for Propane last summer on a pre pay plan which makes me think the ground source heat pump probably would have been the way to go years back. I know the price of petroleum type fuels are going to get out of control. At this time I’m heating a 2000 Sq.feet house and gas hot water for around $650-750 a year.
The thing with ground source you’re starting out with a temperature of 50-55 degrees F. That really makes a big difference when the weather is really cold or hot.
Well almost to Cincinnati. I have to connect with another flight to Detroit. I wish they would book direct flights....I can almost guarantee my luggage will end up in New York. You can’t believe how they have me booked going home, Leaving Detroit to St.Louis Via Atlanta. Maybe they will let me jump out over St.Louis on the way to Atlanta.
It’s 9.00 PM in Detroit and I’m settled in my Hotel. I “jumped†a flight in Cincinnati to get into Detroit early, but when I arrived my luggage wasn’t with my early fight, it went on the later flight. At least it made it.
P.S. When in Detroit people say you usually have three good weather days a year.
Today is not one of them.
Jack Fowler