Mig welder?

Jackman

501 Club
I have a Lincoln 100HD its a flux core welder it can be upgraded to mig , whats the advantages to mig welding is it just nice clean welds or is there more?
 
With proper shielding gas and proper filler wire, the MIG can be used for stainless steel and for aluminum. And on steel, no slag, and virtually no spatter. Gas shielding is not effective in windy conditions.
 
thanks BusDriver I've been testing this unit all morning and I got an idea that it really just a sheet metal welder cause it does not penetrate very deep and the bead is so small , I think it will stay a flux core welder since sheet metal and other small steel stuff is about all I need.
 
My wife gave me a welder for my birthday (end of June). It's the biggest 120v unit Hobart makes. It says it can weld up to 1/4" mild steel and down to light sheet metal. As Bus Driver said, with shielding gas, it can weld aluminum and stainless. I don't have the gas bottles yet; just experimenting with flux core wire for now. It's a blast!! Plan to get the argon/CO2 mix later.

My 1/8" thick steel trailer ramps were in need of some extra cross members (the wheels of my mower kept getting stuck down between the rungs). So I cut an old bed frame up (angle iron) and welded those as intermediary cross rungs. Worked great!

Anyway, said all that to say this, with the right voltage/amperage unit, even a 120v unit is far more than a sheet metal welder. :D
 
I have the Hobart 140 (115V) and love it. I use the argon 75% co2 25%. Big plus with the gas. When welding thicker stuff you need to use a W pattern and with a bit of practice it works great. Grump
 
Hey Grump what do you mean by W pattern :?: I have been using my neighbors Hobart 135 mig with flux core thats a really good unit I did a floor pan in a VW bug every weld was a good one :D .
 
I've had the lincoln 100sp MIG with the gas, the big mill220vt 200amp MIG and a 500amp 100% duty cycle with 1/16'' wire. The penetration depends on what amperage and duty cycle your MIG is, plus how high the wire feeder is set at, with the higher feed setting the duty cycle is what we haveto watch because were running a higher amperage it means more heat on the welder too. I can actually blow a trench in the metal and fill it up with weld. You can change the settings and spray of globual weld too.
I been wanted a smaller 110v MIG to power from my hobart gas engine setup (200amps/4k generator) of just picking up a used wire feeder and power if off the 200amp welder since its a 100% duty cycle that maybe the better way to go with .035 or .045 wire. Using the stargon mix gas (ar/co mix)we get a better quality cleaner weld with less splatter too. I still like the 110vt 100sp and the 125sp MIGS. Bill

On the thicker larger structural steel beams and frames i was using a new lincoln 500amp 100% duty cycle stick welder using 1/4'' to 5/16'' arc rod. I was trying to get the 3/8'' arc rod but it was harder to get from my vendor. He told me i was the only guy in the state using this larger diameter rod. When you want to put down metal really quick in welding the larger diameter rod is the way to go. It saves time.
 
Jackman":3tdo0w2m said:
Hey Grump what do you mean by W pattern :?: I have been using my neighbors Hobart 135 mig with flux core thats a really good unit I did a floor pan in a VW bug every weld was a good one :D .

The W pattern is..I guess instead of welding a straight line you would run the bead side to side filling in more area in the same pass. Hope that helps. Grump http://www.hobartwelders.com/om/0900/o925f_hob.pdf go to section 9-5 and see the gun movement section.
 
Flux core - deeper penetration for thicker material, more splatter. I almost always use flux core in my Hobart 140 but typically use wire feed only for tacking. I much prefer stick.

MIG - looks better, may be slightly stronger. Less penetration may be an advantage with sheet metal.

Gas is expensive but so is flux core wire.

The smaller MIG welders are short circuit mode which may not do well with Al or SS. The gun on the smaller MIGs also may not have a good liner for Al welding. The wire may jam easily.

Don't use the C25 gas for either SS or Al. Argon for both or trimix for SS.


Lots of folks think the 120 volt MIGs are not really capable of much but they are actually very useful. However, get a stick welder if you have a 220 volt outlet and you may find you use the stick welder more than the MIG.
 
My biggest and oldest welder is a Lincoln IdealArc AC/DC 250. Some call it the "tombstone". 300 amp AC, 250 DC and it has 60% duty cycle at full amperage, more at lower amperage. 100% duty cycle at 150 amps or less, as best I remember. Probably weighs 800 pounds, has power factor correction capacitors.
My MIG is 110 amp and powered by 120 volts. It has just 20% duty cycle. But it is an extremely useful machine and most of the time, the short duty cycle is not a problem.
I use the Lincoln on everything heavier than 16 gauge.
 
Back
Top