Hot Rod or racing Guru's

birddog

501 Club
Last fall I acquired a "97" Mustang SVT Cobra with a 4.6 DOHC engine. It has a Vortec super charger and after market oil pan, among other things. I was told that it holds 8 1/2 qts. of oil. The manufacturer of the oil pan says it's a 7 qt. system pan. Other than the installer not calibrating the dip stick, can anyone think of a reason that it should have 8 1/2 qts' of oil? The super charger sure doesn't hold 1 1/2 qts.!

The car has oil issues, including smoking and amount of oil used. I think a lot of the problem is excessive oil in the system.
 
I don't know about any recalibrating of a dipstick. If the original dipstick is in the original position, it should be correct. An increased capacity oil pan should be deeper or wider in the portion that is below the original oil level. Raising the oil level is simply overfilling and usually causes problems (for example dipping the rod caps in the oil). After an oil change, warm it up, let it drain back then simply top the oil off to the original level, using however much oil it takes to reach that level.

By the way, if the oil pickup wasn't extended down near the bottom of the new oil pan, the added capacity won't do you much good. The cooler oil will be near the bottom of the pan.
 
Ricky; I need to get it up in the air to better check for an aftermarket oil cooler, but I don't think it has one. It has an OEM filter and cooler.

Jim; I thought that might be the case, but I read some where (possibly the manufacturers web site) that it was the installers responsibility to calibrate the dipstick. Then there's the fact that it's suppose to be a 7 qt. pan but takes 8 1/2 to fill it. According to the specs for the pan, it uses the OEM pick up, so the pan must be wider.

I guess I'll wait and check for sure if there is another oil cooler and that the dipstick tube is installed properly. I can't believe all the things I'm finding wrong with this car. Bolts loose or missing, clamps and support brackets loose or missing. The bypass on the supercharger was installed backwards.

Also, maybe contact the pan manufacturer to find out if the dip stick does have to be calibrated.
 
birddog":38y1auhb said:
..... I can't believe all the things I'm finding wrong with this car. Bolts loose or missing, clamps and support brackets loose or missing. The bypass on the supercharger was installed backwards.....
Just like with Cubs, some people aren't smart enough to know what they don't know about.
 
birddog":1xnrf93a said:
. . . I read some where (possibly the manufacturers web site) that it was the installers responsibility to calibrate the dipstick. . . .
That may be one of those CYA instructions -- not our fault if you don't keep oil at the right level.
 
In 1970 I bought a 1970 Boss Mustang. It came from the factory with the wrong dipstick. The first time I changed the oil I went by the dipstick and it was 2 quarts over filled.
 
I e-mailed the pan manufacturer late Sunday afternoon, and by 9:00 AM Monday I received 2 answers. They only have 2 pans for my engine and both are 7 qt. system pans.

Neither e-mail actually came out and said that the dipstick had to be calibrated, but they both stated how to do it. They each had their own way of doing it and end up with the correct amount of oil. I liked the one way a lot better and it seemed like it would be a little more accurate. Here's how they said to do it.

" To calibrate the dipstick drain all oil from the system and refill with 6 qts without turning the motor over. Mark this spot on the dipstick as your new full level. From there add 1qt to account for the filter and then run the motor. After running the motor take another measurement and fill to the previously marked line to get an accurate measurement on your ancillary oiling parts."
 
Back
Top