First off tell me if this is a good deal. For about $230 I plan on getting a 5-foot brush hog that has no rear wheel. A 8-foot blade. Which apparently has the ability to spin all the way around. and a one way I believe rear facing dirt scoop with a little bit of rust in Holes about 5 in from the edge of the dirt scoop. And possibly a trailer hitch LOL for about two hundred thirty bucks.
I figured I should add this as well the 8-foot blade was actually a 6-foot blade and the guy welded on two pieces of diamond plate one on each end making it now and 8-foot blade. It's been sitting in his yard for years and probably has some movement issues it does have a bolt that locks each individual position into place.
The dirt scoop as far as I can tell with my limited dirt scoop knowledge is a rear-facing dirt scoop only. About 5 inches from the edge of the dirt scoop there are various rusted holes pretty small maybe the width of a pin or pencil maybe about 5 or 6. I did not research it too much cuz I saw the rust and thought for 25 bucks it was a bad deal LOL
Now here's the question. Brush hog is of a model and make I don't know because I didn't have time to look. The problem I have is it's missing the rear wheel a single Center wheel it neither has the wheel or the bar that would raise it up and down attached to the brush hog. The guy did test it for me and he did lift it so I could look .underneath. Looks like there might be some fluid leakage underneath around the gearbox what I mean by that is there was a kind of moisture spots surrounding that. One of the blades was frozen in place but I think if I hit it a few times it will loosen it so it can swing freely. It's been sitting in the guy's yard according to him for at least a year he bought it off of an auction or something like that. By the way this guy is going to give me one of those huge tires specifically designed for brush Hogs and a mount which does not fit this. And I think I might be able to get more stuff from him. so if I was to weld a tire on there and possibly create a leveling bar do you think that would work and besides that $100 brush hog that has been tested and does run does that sound like a good idea. LOL..
Also the guy is giving me a huge steel bar which is cylindrical. Meaning it's a very heavy steel bar much like what you would use for fencing except it's much thicker and stronger. He's going to give me that and a wheel and a mount off of some other tractor. I could probably get him to give me more stuff as well so for 230 bucks he plans on giving me one brush hog 1/8 foot blade 1 dirt scoop and one trailer hitch with trailer hitch bar also huge metal bar for possible welding big ass wheel and mount for the brush hog. So I just want to know what everybody's opinion is on this I'm going to be picking the stuff up Wednesday. By the way I have a 1948 Farmall H with 3-point.
I figured I should add this as well the 8-foot blade was actually a 6-foot blade and the guy welded on two pieces of diamond plate one on each end making it now and 8-foot blade. It's been sitting in his yard for years and probably has some movement issues it does have a bolt that locks each individual position into place.
The dirt scoop as far as I can tell with my limited dirt scoop knowledge is a rear-facing dirt scoop only. About 5 inches from the edge of the dirt scoop there are various rusted holes pretty small maybe the width of a pin or pencil maybe about 5 or 6. I did not research it too much cuz I saw the rust and thought for 25 bucks it was a bad deal LOL
Now here's the question. Brush hog is of a model and make I don't know because I didn't have time to look. The problem I have is it's missing the rear wheel a single Center wheel it neither has the wheel or the bar that would raise it up and down attached to the brush hog. The guy did test it for me and he did lift it so I could look .underneath. Looks like there might be some fluid leakage underneath around the gearbox what I mean by that is there was a kind of moisture spots surrounding that. One of the blades was frozen in place but I think if I hit it a few times it will loosen it so it can swing freely. It's been sitting in the guy's yard according to him for at least a year he bought it off of an auction or something like that. By the way this guy is going to give me one of those huge tires specifically designed for brush Hogs and a mount which does not fit this. And I think I might be able to get more stuff from him. so if I was to weld a tire on there and possibly create a leveling bar do you think that would work and besides that $100 brush hog that has been tested and does run does that sound like a good idea. LOL..
Also the guy is giving me a huge steel bar which is cylindrical. Meaning it's a very heavy steel bar much like what you would use for fencing except it's much thicker and stronger. He's going to give me that and a wheel and a mount off of some other tractor. I could probably get him to give me more stuff as well so for 230 bucks he plans on giving me one brush hog 1/8 foot blade 1 dirt scoop and one trailer hitch with trailer hitch bar also huge metal bar for possible welding big ass wheel and mount for the brush hog. So I just want to know what everybody's opinion is on this I'm going to be picking the stuff up Wednesday. By the way I have a 1948 Farmall H with 3-point.