Drilling for oak beam connecting plates

Paul_NJ

501 Club
Finally had a concrete floor poured in my old bank barn before Winter set in. Boy it sure begins to fill up quickly!

IMGP0765-vi.jpg


Those 6x6 post and beam timbers are all setting in place without fasteners. I'd like once and for all to add steel connecting plates to reinforce all of the junctions. I think 1/8 inch (10 ga) thick steel would be sufficient. I'd prefer to use a plate on each side of the junction bolted through. However, my experience drilling accurately through 6 inch oak beams with an auger bit in an angle drive electric drill hasn't been very good in coming out the other side in an exact spot . . . the grain seems to pull the bit as it wishes. So how can I line up the holes in two opposite plates? Yet I've seen beam junctions like this sandwiched between two plates. . . how do they do it?? I suppose I could use lag bolts on each side, or only use a single plate on one side, but I'd prefer the sandwich approach if possible.

Any suggestions how to do this?

Thanks
 
Paul:

Just my opinion, but the best way and the most accurate is by far a ship's auger in either an electric drill or a brace and bit. However, they come in different qualities and the cheaper they are, the more deflection you will get.

An electric drill will do it faster, but with speed comes an inherent built in risk factor of the bit wandering - probably due to heat buildup :?: With a brace and bit, it takes time and muscle as well as a lot of endurance (but that was how they did it when your barn was built...).

If you go to a Good Fastener Supply House where they deal with the trades that use this kind of stuff, they can accurately help you with the correct choice of bit for the application you wish. It can get pricey for a good bit for a 1/2 drill, but -- well worth the price to get a large job done quickly.
 
Lacking a barn beam boring jig (there was such an animal), one way to get it closer would be to drill in from both sides. Drill in half way from both sides and your margin of error should only be about half of that drilling all the way through from one side. If you go slowly and carefully you should get close enough.
 
Brad point drill bits will give you a nice straight round hole with no blowout when the drill exits. Any woodworking supply should have them. Put your plates in place, clamp them and drill. A HS brad point will cut through the plate and the wood.
 
Paul, let me put my 2 cents worth onto this discussion. I always thought that black painted metal would be appropriate for the bracing. It would fit the period as the rest of the decor. I was sitting up all alone last night pondering your problem. And one pregnant thought led to another. Two things really; 1) What if the 2 plates were connected by only 1 bolt, or threaded rod. If you wanted additional support, the plate could be predrilled for lag bolts. 2) What abou the structural reinforcing plates similar to those used on trusses? That may not look too out of place, and it would be cheaper and easier.
Larry
 
Rudi: I've got a Milwaulkii boring auger bit, likely it's more the operator's (me) aim that's off.

Bigdog: That's it! . . . that's what I needed all along . . . a barn boring jig! That's a thought, maybe I could make a jig to keep the drill bit square all around.

Lil Red: good idea . . . drill thru the second plate in-place. That would have to line-up.

Larry: I agree, they will be black. Not sure what the reinforcing plates you're referring to look like though . . .the ones I've seen are pretty thin sheet metal. I thought I'd need thickness of at least 1/8 inch, maybe more. I've seen photos in books of timbers connected like that . . but can't find anyone who sells them. Probably have to make them.

All good ideas! Maybe I could attach the plates with small lag screws to hold them in place: front plate is predrilled, the back is not. Make a jig to hold the bit straight. Drill thru to, and then through, the back plate like Lil Red suggested. Maybe I could switch from wood auger to HSS once I'm thru the wood. One large (5/8 or so long bolt may be enough). That may work!

Thanks for the ideas.
 
Paul:

I was kinda sleepy when I posted that I think.. I should have also said that there are guides that you can either buy or rent (depending on where you are I guess). They are heavy duty and will hold many different types of power drills.. They are used for pole barn or heavy timber Post-&-Beam construction. Many versions have been around for decades at least..

I did a guick google and found a few interesting sites.. but not a lot pertaining to boring/drilling large wooden beams... and I used a number of search strings.. but with some interesting results.. like Femoral Drill Jigs (orthopedic surgery tool??) At least the one at TimberTools is realistic.

TimberTools.com
img_Drill-Guides-pic.jpg
 
Paul,what I did when I needed to get a straight hole through a beam I bought a cheap bench top drill press and mounted it to the beam with clamps.This may not be a good option if you think it will be the only time you use it.In my case I figure I'll need it again plus now its on my bench for regular use.I have also used the drill from both sides method with good success. Mark:
 
A pipe flange with a short piece of pipe in it screwed to the beam is a keep it simple, keep it cheap solution. If the beam is wavy use a block of wood with shingles for shims. Still simple and cheap. I like simple things. They make me feel right at home. Cheap things, well I am part Scotch

bill
 
Thanks to everyone for all of your great ideas, but Bill, you win the prize in my book. A pipe flange and pipe nipple as a guide . . . now that's ingenious! And inexpensive. My kind of solution. I'm going to try it!

Thanks!!
 
Couple more ideas I've seen.

1) U shaped strap that goes over the bean and is fastened to the post on each side.

2) L shaped plates the width of the post, holes predrilled, and lag bolted to the underside of the bean and to the post. Two plates per post.

Eugene
 
i think if you used 5/8" x 5" lag bolts and predrill your holes 1/2" and screwed the lag bolts in with a wratchet youd have just as must strength.
 
Paul,

Just my two cents; one could drill the proper size hole in only one plate.
Then set in place on the beam and clap in place and drill as straight as possible using a level and square. Then put the bolt through the plate and beam and mark the "undrilled plate" and then drill the hole in the plate. You can use chalk on the end of the bolt or carbon paper to mark
the plate. This way the holes should then line up.

I have done this several times over the years and has always worked
for me. If it is a little off it should not matter.
 
Paul, not sure if you want to invest any any more tools, but there are small portable drill presses (both Sears & Harbor Freight carry them) that simply chuck into the chuck of your electric drill.

It has two rods on each side to guide the drill in a straight line/motion and the base can be set up at different angles.

They run about $20-$30. If you lived close, I'd let you borrow mine. I bought mine to drill the benchdog holes in my woodworking bench. It worked fine and the holes stayed straight.
 
I've built a small barn recently. I suggest certain connectors for consideration. I used Simpson Strong Tie products which are available from my nearby Home Depot. OS or OHS135 which have a notched edge. or PSPC218PC or PS418PC which do not. These are black. PS 720 is galvanized. Other companies make similar products.

Richard
 
Hope I'm not too late for this but a friend did the same thing with a support beam in his barn and he cut 2 pcs of plywood the same size as his metal plates and clamped them to his post and beam then drilled his holes and transfered the holes to the metal plate, drilled them and bolted up just fine. By drilling through everything and transfering the bolt hole pattern, things will line up perfect and his 5/8" bolts lined up perfecto. :) :D :D . dave
 
Back
Top