Drill Press Problem

BIGHOSS

501 Club
I have an old standard garden variety floor drill press that has a problem. The drill spindle will not retract fully. It lacks about 2" going to the top. Everything else works as it should, but now I only have about a 2" stroke. In order to drill a deeper hole, I have to keep cranking up the bed with the drill bit still down in the hole.
I have taken it apart as much as I can figure out how. I havn't been able to pull off the top pulley to let me see down into the moving shaft. I even tried a gear puller but it will not budge. When trying to force the spindle up with the lever, there is a fairly hard stop. I am thinking that a gear tooth could have chipped and is blocking it. But with not being able to get the spindle loose, I am stuck.

Any thoughts?
 
I don't have a quill stop that I know of on the left side. There is a scale with pointer on the right side. But, I will look again.
 
If you know the manufacturer and model number, you may be able to find an exploded parts list on line.

If you can see the key holding the pulley - it should pull off - perhaps with a bearing seperator. If there is no key check to see if the pulley is threaded onto the spindle.

The quill stop on mine is a thumb screw and dial/scale located on the right side of the head. To set or adjust the quill stop, loosen the thumb screw, then move the quill to the depth desired and then tighten the thumb screw.

Some drill presses use a threaded rod and nut to limit the quill movement. This system is mounted on the side of the head.
 
It might be simpler than a chipped tooth. Something may have fallen into the gear teeth and is jamming it up. You could try flushing it out with carb cleaner and blowing it out. But it might also make it fall in farther.

Billy
 
I belong to a woodworking website at Old Wood-Working Machines (www.OWWM.com). They also have a discussion forum located at www.OWWM.org. Joining up is free.

If you know the drill press manufacturer and model number, there are many manuals and reference documents to access. They are also a great help with such questions.

Hope you get it working again.
 
It has been a few days since I started working on it, but I seem to remember a nut on top of the quill pulley. I never thought of trying to screw off the pulley. I need to check this out. I will post some pics as soon as I can. I am having catarac surgery tomorrow, so that will slow me down for a few days.

As for the brand. I bought it used several years ago. But, it is the garden variety DP that you see every where with different brand names. It seems to me that one factory is turning these out in China or Tawain with several name brands. Because it looks as if the parts will interchange.
 
Ron:

If it is a Rex-Cut model -- marketed under many different tradenames, manuals and parts lists are not difficult to obtain. Two of the most popular makes in the US and Canada are Grizzly and Busy-Bee. Busy-Bee now markets their products as Craftex. King tools also distributes Rex-Cut.

When you get the model number I am pretty sure we can help locate a parts manual.

Edited: to add missing data
 
BIGHOSS":8wn5jifi said:
I don't have a quill stop that I know of on the left side. There is a scale with pointer on the right side. But, I will look again.

That should be where the quill stop is at.
 
Rick, my dp looks just like the first one on the list, the Delta 12". It looks like I need to remove the spring assy and related parts on the left side to let the lever shaft slide out to the right. This will let me look inside to see what is going on. I have been reluctant to take this off. I don't have a good history of replacing coiled springs that go spo-ingggg. Can we get the Sears drawing copied here so we could see it better and decide what I need to do.
 
We'll see how this shows up :shock:
normal_deltadrillpress.png
pic borrowed from online Sears

Rick
 
Thanks Rick, that's it. Looks like I need to remove the jam nuts on the left side to take off the coil spring assy. I can't tell how the spring is connected to the shaft. By the way, I could not locate the number for the shaft on the drawing. I am talking about the splined shaft that the handles attach, that lowers the quill up and down.

As I said earlier. I am leaving in a few minutes for cataract surgery on my right eye. I will have the right one done today and the left one in two weeks. So, I don't know how I much I can do for a few days. Besides, the temp in my shop is about 25 degrees right now.
 
I'm thinking from experience there is a sliding key on the shaft that keeps the spindle turning all the time. Depending on which setup you have there is a sliding bronze bushing involved too on some of them. Something is binding in this area. (maybe) On the other hand it could be the geared rack setup too, it can have a chunk of something stuck/jamming it or some teeth are missing too. I have welded teeth on an older pinion rack setup and filed them to match. Most of my experiences are with the older heavy castiron pedistal drill presses. Most of them operate on the same theory anyhoo.

Merry Christmas and Happy Holidays to all which ever applies to be religously correct. Merry Russian Christmas too.. Happy New Years too. Best wishes for the holidays to everyone, Godbless, Bigbill

We have the new grandson this year and he's just starting to come to life now. I got him a tickle me elmo. I was looking at a train set for over $1,000 but its too soon yet. He has a 22cal pump rifle already.
 
Back
Top