Basement leaking even with a small rare rain

Little Indy

Well-known member
Guys and gals,

Need suggestions about drains for basements> Here in NE we have been having a drought, that drys the earth which then shrinks. This happens under the footings as well. This house was built to code in the 50's and not much more. My father, a general contractor, did not have many nice things to say about fellow contractors who built to mininal standards. The foot cracked and then the walls. The basement now leaks. This happened in 1982. I dug down to the footings then. Tared the walls and put in black corrugated drain tile. None of this had been done. Well the fix lasted until this year. A structural engineer has seen the walls and passed the building. I dug down to the footings with a backhoe. Took off the insulation I placed in 1982. Cleaned the wall. Took out the old drian tile.
This is my plan. Please point out the flaws.
1]Clean walls and repair cracks with epoxy.
2] Cover walls with one of the new rubber like coverings and the a tough membrane the has a 1/4" air gap that allows water to head for the bottom drain tile.
2] Use smooth 4" PVC with holes on the side.
3] Put in clean outs.
4] Put plastic membrane under the PVC to help keep water from going under the footings and seeping into the floor area and another that allows water but not roots to enter pipe.
5] Put about 2-3' of pea gravel around and above the PVC.
6] Fill the trench to within 3 feet of the surface.
7] Take the old corrugated pipe and place in trench.
8] Cover with old gravel.
9] Fill trench so that the ground slopes away form the house.
10] At a distance of 3-4" from house have earth start to form a shallow V which will drain water along then away from house.
11] cover the V with pea gravel and then sand.
12] Replace brick of patio.
13] Curse builder first in English and then Calabrese Italian as footings probably needed more rebar.

Richard
 
richard,
you prety much covered what is going to be needed. since youre going all out and asking for any suggestions, how about an outdoor sump pump? i did a residential flooding problem for a subdivision in aroura, ohio. several houses had the same problems as you are describing, and an external sump pump got rid of alot of water problems. the price for the setup is approx $400 to $500 if you do your own wiring too, but if you can find a decent pump for a good price it will be much cheaper. home deport or schmowes has everything. what kind of epoxy did you use anyway? good luck!
john
 
Richard,

Personally, I think you’re on the right track probably with somewhat of an over-kill when back filling around the foundation. I really don’t know about the clay and even the plastic clay problem you may have like we have in the area I live in. Actually water gets trapped under the surface around here and goes to the path of least resistance, which may be through a crack in a foundation or concrete floor.

I don’t know anything about the epoxy you are talking about. I know there is an epoxy weaving method that is used around here much like sewing cloth together. I’ve heard about the membrane method which is much like a swimming pool liner.

I think you are over-killing with the 4” PVC pipe. I think all you need is the 4” black corrugated pipe that comes in 100 foot rolls. I would put it on top of the footing with the valves of the pipe to the side. Cover the pipe with 2” gravel 15 to 24” above the pipe. Around here we put straw on top of the rock to keep the dirt from falling through. The straw will dissolve after a period of time so maybe another product should be used in your area if you want. Depending on how much rainfall you get, I would a least run two separate 4” drain pipes from the house, splitting the front from the back. Make sure your gutter down spouts drain the water far away from the house. Don’t connect them to the foundation drain. Back fill the foundation, sloping the dirt away. Remember you will have a lot of settlement after the backfill for a period of time, so don’t haul any dirt away.

I know there are a few home builders on this site; maybe they will give you a few pointers.

Jack
 
Jack wrote:
The straw will dissolve after a period of time so maybe another product should be used in your area if you want
The suppliers sell a permeable membrane which will keep the dirt away from the footer and last a very long time.

If possible, it is a good idea to have a sump in the basement which would collect the drainage pipe water. This would require running pipe through the footer. In our county, the building code specifys that the drainage tile is laid inside and outside of the footer with crossover pipes every ~8 ft.
Larry
 
I have a 100 year old house. Part of the foundation is limestone rock sitting on hardpan and bedrock. Some leaks with a very heavy rain.

I put a sump pump under the basement floor in the corner where the biggest leak occurs. I took a skill saw with masonary blade and cut grooves in the floor ending at the sump pump. Grooves carry water to the sump pump.

Eugene
 
Larry wrote:

In our county, the building code specifys that the drainage tile is laid inside and outside of the footer with crossover pipes every ~8 ft.

The code here is the same but without crossover pipes every ~8 ft.

Larry, I was thinking, if you put crossover pipes from the inside out, wouldn’t the water drain from the outside toward the inside. The outside drain pipe is setting on the footing and the inside drain pipe is below the footing. I know it wouldn’t make any difference because it’s all going to the sump pump, but in my preference I don’t like water setting in that sump if something happens to the pump.

I have mine independent from the outside to inside and the sump doesn’t get any moisture in it at all. I guess I’m lucky. I live on acreage and was able to run drains from the footing drain away from the house. I know in housing developments everything has to go to the sewer, which is why maybe everything goes to the sump and only one drain is needed.

Eugene wrote:

I have a 100 year old house. Part of the foundation is limestone rock sitting on hardpan and bedrock. Some leaks with a very heavy rain.

Years ago I lived in a house like yours. When the basement started leaking all I had to do was put some dirt around the foundation sloped away from the house and it stopped. I guess I lucked out again.
Boy that house was beautiful; it was listed as a century farm in the Missouri Archives. The original log cabin was still on the property that was built when the family came over from Germany to this country.
 
Jack wrote:
Larry, I was thinking, if you put crossover pipes from the inside out, wouldn’t the water drain from the outside toward the inside.
Yes. I guess that's the idea. What causes the basement to leak is outside pressure on the basement wall. It you can relieve that pressure, allowing the water to drop to a level below the floor. It can then be pumped away, keeping the floor dry. About 5 years ago I built a house on a lot with some standing water issues. I thought that I could create swales that would divert the water from the house. I was partially right, but still had water. So I installed 2 sumps at opposing corners. Instead of hiring a company to spray the basement foundation, I bought the 5 gal. cans of foundation coating and forced it into every nook and cranny in the concrete. Any concrete egg shells I found, I asked the workers to use the epoxy concrete mixture to completely fill the voids. It's been 5 years and I haven't heard of any leaks to this date. Of course, after the project I moved to a different state! :oops: Just joking.

Suppliers sell sump pumps with a battery backup, so if you power goes off, the pump will keep pumping.

My 2 cents, Larry
 
Years ago I lived in a house like yours. When the basement started leaking all I had to do was put some dirt around the foundation sloped away from the house and it stopped. I guess I lucked out again.
Boy that house was beautiful; it was listed as a century farm in the Missouri Archives. The original log cabin was still on the property that was built when the family came over from Germany to this country.

We also painted the inside rock and concrete walls with a white sealer (Drylok). It works pretty good. Drylok eliminated most of the seaps above the floor. We also raised the dirt level around the foundation on the uphill side of the house and diverted some of the run off away from the house back into the street.

I think the biggest thing on keeping the water out was putting in the sump pump. The sump pump appears to take the ground water down to a level below the floor. We used to get seepage comming up from below the floor.
 
Something else that will help, though probaly won't completely solve the problem of leaking after a long dry spell is to lay sprinkler or soaker hoses around the house and use them to keep the soil soaked up so it doesn't shrink away form the walls.
 
I thought I might give some of the brand names for the above fix. Some of the stuff is available from Menards.

The stuff with which I am going to paint the outside walls is called Blue seal. Expensive but does not harden like tar does. $85 coveres 150 sq ft.

The membrane is Platon. 7.5' by 65'. Don't remember cost.

The epoxy is the stuff with which the KS Dept of Roads repairs concrete bridges. If you have ever been to KS you know they have many concrete bridges. I think in the 30's and 40's they must have gotten a good deal on the forms. The bridges all seem the same. If I can't get my hands on the stuff I might use Hydroseal 3000.

Richard
 
Hi Richard

You do not say what type of soil you have. But I was told and it worked for me. Put a clay cap around the house. That is one foot higher than the suronding ground and tapers off to the original ground surface over four feet. You could also put a plastic sheeting liner under that clay cap. That has worked for my house except under the deck which I haven't gotten to yet.

Good luck Billy
 
I have been doing a lot of looking and reading about basement- foundation repairs.
I am new at this way to repair foundations so I have no practical experience but I thought I would pass along some of what I learned.

Makes a big difference whether you have a solid (poured, brick, stone) foundation or one with cavities (concrete block).

I suggest you don't use epoxy in block foundations or walls as you will be using alot of very expensive epoxy. I think that just about anyone who can repair cubs and can repair their walls. I found these companies by googling "crack injection " foundation. simpsonstrongtie.com, emicole.com, appliedtechnolgies.com, epoxysolutions.net

Since I have a block wall I will be trying polyurethane injection behind an epoxy patch. For some of the larger cracks I will try a strap made of carbon fibers applied to the wall with epoxy.

Probably overkill but then I don't want to do this again. Let my children worry about it.

Richard
 
I know that we do things differently in Europe but may I add my few €s worth? I'm waiting.
Well as there is no answer to my question, I will reply antway!

What I would be interested to know is if you are on a slope so that any drain you put in can be laid to slope away from the building in some way?
The perforated drain in rolls is ideal for this job, not solid.
when you dig down go deeper than the foundation to take any periferal hydraulic pressure off the foundations and to a certain degree the concrete slab inside.
We use a corugated plastic sheet called DELTA MS against the wall which keeps an airspace to take out any moisture retained in the wall then backfill with 2 to 3 inch rocks to the top with nothing covering this.

See http://www.deltams.com/

The reason to use large stones is to keep a circulation of air through them therefore drying the surrounding masonry and letting air get up the back of the Delta MS.

My last success at this was a house that was built into a bank in fairly clay soil but with shale pockets.

The basement walls were covered with soil at the front of the house up to 2.5 metres high.
Even with slight rain one could watch the water coming through the mortar and running down the inside of the wall. I should say that the house was built in 1930 with 2 foot thick stone walls with clay used as mortar (usual practice here at the time, yes right up to roof level!).
I carried out the above procedure and wow even when there is the greatest flood dimension rain that just flows over the surface of the ground that wall inside stays dry as a bone and the drains run full bore. This was done before I had discovered DELTA MS so the stones were just straight against the wall of the house. Another house I did the same but used DELTA as an aditional aid it tends to let the wall breath.
I found one spot in the cellar floor as well where it was always wet and before putting the concrete slab in I ran a series of 1 1/2 inch perforated drain in a roll from the damp areas into the aforesaid periferal drain system and it is dry as dry.

When there is even a small wind one can feel air coming out of the end of the drains, this is coming in through the large stones used for backfill down the wall and into the perforated drain.

PS if you go for this system don't put a covering on the drain at all, no need, indeed it can hinder the air circulation.

I hope that this can help you a bit?
PAT
 
Pat wrote:

I know that we do things differently in Europe but may I add my few €s worth?

Pat, en France vous faites des choses mieux !
I’m not a builder like Pat, but I think this is a great system. What I like about it; not only it drains the water and seals the foundation; the air flows through it and dries the moisture out.
 
Patbretagne":3p2iwc6f said:
See http://www.deltams.com/

The reason to use large stones is to keep a circulation of air through them therefore drying the surrounding masonry and letting air get up the back of the Delta MS.

My last success at this was a house that was built into a bank in fairly clay soil but with shale pockets.

The basement walls were covered with soil at the front of the house up to 2.5 metres high.
Even with slight rain one could watch the water coming through the mortar and running down the inside of the wall. I should say that the house was built in 1930 with 2 foot thick stone walls with clay used as mortar (usual practice here at the time, yes right up to roof level!).
I carried out the above procedure and wow even when there is the greatest flood dimension rain that just flows over the surface of the ground that wall inside stays dry as a bone and the drains run full bore. This was done before I had discovered DELTA MS so the stones were just straight against the wall of the house. Another house I did the same but used DELTA as an aditional aid it tends to let the wall breath.
I found one spot in the cellar floor as well where it was always wet and before putting the concrete slab in I ran a series of 1 1/2 inch perforated drain in a roll from the damp areas into the aforesaid periferal drain system and it is dry as dry. When there is even a small wind one can feel air coming out of the end of the drains, this is coming in through the large stones used for backfill down the wall and into the perforated drain. PS if you go for this system don't put a covering on the drain at all, no need, indeed it can hinder the air circulation. I hope that this can help you a bit? PAT

You guys have been a big help and have provided me with a lot of support. I had been through this in 1982. Back then I dug down with a backhoe; knocked a corner off the foundation (I called my dad who was a general contractor and house builder for advice; he was ROF-LOL on the other end of the line but gave me good advice about repairing that corner). I put tar on the wall and insulation and a corrugated perforated drain tile which worked until this fall. I found out that a three foot section was filled with mud and roots.

But the drought had shrinked away the earth and the foundation cracked. I had a structural engineer look at it. I then fired up the backhoe again and dug down. The house is a walkout with the slope to the west and front to the east. 1/2 of the east wall leaks and all of the south wall. The earth is a heavy clay with a 3 ft layer of top soil. The foundation is concrete block. This is the plan.

1] Clean wall and cover wall with Blue Seal by painting with rollers, a rubberized membrane. When dry flexible and wateproof.
2] Fill cracks with polyurethane through straws after filling cracks with a patch of epoxy putty.
2] Cover Blue Seal with another membrane similar to Delta MS this allows water to drain down the wall as it has 1/4 inch air gap between itself and wall. And cover that membrane with insulation.
3] Place clear plastic membrane at bottom of trench which is below bottom of foundation by a few inches about 5 cm.
4] Place on the clear plastic a solid perforated drain PVC pipe with holes 2/3rds up the sides about every foot. This goes around the footing and will drain water from the east wall to the south & make a bend & then west until the end of the foundation where it will be connected to a solid non-perforated PVC pipe which continues for another 50 feet down a slope to a bunch of rocks. The perforated PVC will be covered with a long gauze like sock to let water in and dirt and roots out.
5] Cover the sock covered perforted PVC pipe with pea gravel about 2 to 3 ft deep (1 meter)
6] Fill trench 1/2 up with dirt. Place another plastic membrane in trench and then place the old corrigated perforated pipe in bottom of trench after cover the rest of the sock. (It was 100 ft long).
7] Fill trench with the grave and now sand that had been around that pipe before.
8] Fill trench with dirt. Then overfill trench with more dirt about a foot higher than before.
9] Time passes and dirt settles. More dirt to previous over fill line. (house has a brick veneer). This will be a heavy clay on wich I will plant buffalo grass.
10] Shape cross section of fill like a shallow V with drainage pointing south. Fill with pea gravel and then sand over which is the brick of patio.

If I had a solid foundation wall (poured concrete, brick or stone) I would have crack injected the cracks with epoxy not polyurethane. Google crack injection foundation repair. You will find various suppliers to sell you a DIY kit for about $120 per crack.

There is a product out there that caught my interest. You paint it on to bare concrete and penetrates about 4" and reacts with free lime in the concrete to form a lime-epoxy bond. Since I tared the walls before not suitable for me.

Richard
 
Back
Top