4 1/2" & 5" hand grinders

BigBill

501 Club
I had a few of the cheap 4" hand grinders i purchased from harbor freight for $9.99 and i burned out about 4 of them so i went looking for a good buy on new hand grinders. I purchased the Jepson brand from northern hydraulics which lasted me from around '86 till just a few years ago. (4") My 7' jepson grinder is still running today. Well i found the 4 1/2" hitachi 9,5 amp for just $99 brand new ( http://www.reconditionedsales.com )
and the bosch 5" 9,5 amp for just $99 too.( http://www.CPOtools.com ) and the 5" grinding wheels at http://www.lehighvalleyabrasives.com at very affordable prices too. There offering the 4 1/2" x 7/8" wheels right now for just $1.15 each too. I'm finding out the harbor freight grinding wheels burn right up with the more powerful grinders so i have to purchase the better quality grinding wheels now too. The harbor freight grinding wheels are good for the 5 & 6amp grinders.

I purchased a 4" hitachi grinder and had problems with the on/off switch and they replaced it right away with no problems. They get my vote for quick customer service too they were outstanding.
My new 9,5 amp hitachi grinder is an animal and you have to really hang on to these powerful grinders too. These seem to be really heavy duty.
And the Bosch grinders are awesome too with a great selection at affordable prices. If the new 5" grinder works well I may go after the 6" grinder next. Bosch has a larger selection of hand grinders and wheel size.

The bottomline is no more cheap power tools for me its just wasted $$ when they can't do the task at hand. I may even get a Metabo grinder next to test drive that one too and see if it works out too. When i was working i purchased new AEG grinders but i no longer see them offered here. I had good luck with the AEG grinders for many years. I just want the highest quality hand grinder that i can buy for the lowest cost.

The only thing i do to the hand grinders when they are brand new is to add moly to the gear drives and they seem to run alot quieter and last a longtime too.
 
The only thing i so to the hand grinders when they are brand new is to add moly to the gear drives and they seem to run alot quieter and last a longtime too.
Really, you take your brand new tools apart and install molybdenum grease in the gears. Cool.

Concur. Buy quality tools.
 
I have a couple of the cheap $10 grinders that I use for light duty stuff, they work ok for that and when they fail, I just pitch em. For more severe duty, I have an inexpensive Black & Decker which has served me very well for the past 10 or so years. I also have a DeWalt that has been very reliable. All the above are 4 1/2 grinders but I can run 5" discs on all but one of the cheapies. I don't like switching wheels around, so each grinder is set up with a certain wheel type. For some jobs I may have 3 or 4 grinders on the job.
 
Eugene":8ubhwwcd said:
The only thing i so to the hand grinders when they are brand new is to add moly to the gear drives and they seem to run alot quieter and last a longtime too.
Really, you take your brand new tools apart and install molybdenum grease in the gears. Cool.

Concur. Buy quality tools.

Hearing the gear noise on any grinder when you turn it off makes me cringe. I just have to lube them with moly then there quiet plus they last a long time if there a quality grinder.
 
BigBill,

The Metabo grinders are very good quality, we had several at my former work (construction equipment repair) and they held up real well to the abuse dished out daily to them. The best one was an old Souix 7 inch grinder that was out of the fifties, it was a beast. Milwaukee Skill Saws were the only ones that would hold up to cutting aluminum sheets without burning up or breaking the gears.

You can not beat the low total cost of owning quality tools.

Thanks for reminding us

Mark
 
In years of doing mobile welding I find Milwaukee and Dewalt are the ones that hold up. The 7" Milwaukee grinder was the standard until the 4"came out.
A lot of people like Makita, but I find they don't do well on DC current.
 
Cool Bill

I have to say I really hate the on off switch on those 4" grinders. I ground a hole in my index finger two weeks ago with my Dad's el cheepo. I found a 5" at TSC for about $35 four years ago. It has a trigger switch and is set up like a big grinder but is about the same weight and size as a 4". I use it alot and it has held up good for me. But I like your :idea: of putting some moly grease in it. I also have a 7" dewalt I got at a yard sale for $40. But it really gives the forearms a work out when I have to use it.

Billy
 
Back
Top