Broken Fastener found behind clutch inspection cover

jobbyjim

Active member
I found the IH-marked head of a 1/4" hex head bolt and lock washer (pics attached) laying on the top of the clutch inspection cover plate when I went to apply grease at the end of mowing season. It is pretty gunked up inside there but I couldn't see a broken stud anywhere. I have a 1965 Loboy and have never experienced a clutch issue, the tractor shifts fine. I last applied grease up in there in March and the fastener remnants weren't there. Can some one identify the source and if this means I have to split the tractor? Am I living on borrowed time using it as-is?fastener.jpgfastener 2.jpg
 
if its a 1/4" bolt the only one inside there is the bolt that holds the throwout bearing holder together, maybe left from past repair ? if its broke could be replaced through the inspection hole
 
Looking at Messicks site it looks like it could be the bolt head of a 1/4-28 bolt used to clamp the yoke to the throw out bearing. The diagarm shows a left and a right half of the yoke. 1/4-28's attach them to the sides of the throw out bearing. Looking inside, both halves look to be in-place on the throw out bearing. It doesn't look accessible through the inspection hole.
 
one bolt goes in the middle of the 2 fok halves, look in the hole, behind the bearing you see the bolt, if you do not see the bolt its gone, clutch would not work well either
 
If you go back to the printed catalogs, scans of which should be in the Resources here, you will find the hardware listings directly under the part they belong to. The 1/4-28 x 3/4 is under the 2 yoke halves. If that bolt is missing, all that is holding the bottom of the yokes together is the pin that attaches the operating rod. That will not hold the yoke halves tight together. The throwout bearing may not be firmly gripped. So in my opinion, you are on borrowed time. As others have said, you should be able to verify and replace through the hand hole.
 
I believe this is what Jim is referring to:


Look under Group 7 "Drive Train", Pages 3/4. Part# 21 and Part #22

#21 -- 353 239 R2 -- YOKE, CLUTCH RELEASE LEFT SIDE. Cub Tractors w/Serial No. 32229 & Above, All Cub Lo-Boy Tractors

103 024 -- NUT, 1/4-28 HEX
181 313 -- SCREW, 1/4x28 x 3/4 HEX-HD CAP
103 -319 -- WASHER, 1/4 MED LOCK

Part #22 is simply the Right Side yoke half.

.My guess is it probably seems okay for now because what's left of the bolt shank is still in place, but it will most likely wiggle out over time with no head to hold it. So id agree with Jim on "borrowed time"
 
You nailed it, the hole is empty and the just the pin is holding the halves together. I'll fish around with a magnet to see if I can find the rest of the bolt and the nut. I got big mits, will be a tight fit getting the new one installed. Thanks guys.
 
Hi,
Below are pictures from TM Tractor Parts of the bolt in the throwout bearing holder.
This is the newer style holder, like a LoBoy would have.
 

Attachments

  • Cub clutch throwout bearing and holder.jpg
    Cub clutch throwout bearing and holder.jpg
    19.4 KB · Views: 10
  • Cub clutch.JPG
    Cub clutch.JPG
    17 KB · Views: 10
Hi,
Below are pictures from TM Tractor Parts of the bolt in the throwout bearing holder.
This is the newer style holder, like a LoBoy would have.
Wow, now seeing a picture just unlocked a mildly traumatic memory LOL. I remember having to do this repair in the field a long time ago. If I close my eyes I can feel the sweat, frustration, and the tactile sensation of trying to get the stupid nut threaded on as it wobbled on the end of the bolt threads. I think we ended up splitting that tractor towards the end of the season because the TOB was already buggered up from the fix coming after the damage was done and discovered.
 
Back
Top