Got a project that you are working on that is not a tractor? Maybe a barn to hold your tractors or just fun stuff like woodworking, glass, tools, sheds, gardens, custom implements, etc., this is the place to talk about it.
Moderator: Team Cub
I go to a few 4x4 swap meets every year and have wanted to make it easier to load or unload Jeep rear ends on or off my trailer while it has a rolling chassis on also. Most of the time the heavy stuff has to be tucked under the chassis. My buddy has been a welder for over 50 year in his family welding business. He has made several trailers over the years, so I stopped in for a visit. At first I just wanted some sort of temporary extension that could drop in the side pockets. He talked me out of that because he said a temporary set up would be heavy and I would end up just leaving it on. He said a permanent solution would be as strong, if not stronger, and cheaper in the long run.
I told him to go for it, so he added about nine inches on each side in front of the fender keeping the overall width to less than 102”. This will make loading or unloading easier, but will also give me a place to set tool boxes too if need be. It is even plenty strong to allow a Cub to be driven or pulled over the side.
Here it is in its original form.
The welder cut the rub rail and pockets off as a group, fabbed an extension and welded the rub rail/pocket assembly back on. I asked about gussets and he just smiled.
Once I topped it with a new board it was even with the rest of the deck. I have a few boards to replace so I will replace the new boards with oak planks when I redo the rest of it.
Wow, that looks great! I will be replacing some of or maybe all of my deck boards in the near future. My question to you is what kind of preservative would be used on the wood?? Don't want to spend too much on it, just know it needs something as the original boards have begun to rot after 10 years. Won't be able to use Oak either.
Thanks in advance for any input. Steve K.
Nice redo Barnyard. Might do that to mine too.
A good brand of water sealant like Thompson's should do the trick ? That is what used. Even untreated mine usually last 20 years out in the weather.
Member Chapter 42 IHCC
1970 Farmall Cub
1946 Farmall B
1942 Farmall M
1200 Cub Cadet
Steve, I used a product called Penofin to do my trailer deck. I since found out they have a formulation for pressure treated wood.
Thanks for the info on the Penofin! Your trailer looks pretty darn nice, too. I'll try adding the jacks to the rear of my trailer, too. Great idea, thanks again. Steve K.
Great work Bill !!! Give a smart guy like you a welder and the sky's the limit !
REMEMBER: Keep it correct or you may face the
I like what you had in mind, extensions are always good What your buddy accomplished makes a lot of sense and the execution is really cool. I like his gusset idea - that is the key ingredient. Makes for a very useful multiple Cub hauler
Bob, if you have ever seen my welding you would know I didn't do this. Gary Dotson can tell you, if I had done this I would be afraid to lay a feather on it for fear of the side falling off.
Here are a few more shots. I just need to fill the gap until I put a new board along the front. Once the weather warms I will pull it apart and get some paint on it all
Here is how it looked before.
The welder let his apprentice take a shot at welding some of it. I am confident it will hold up. For what Bill charged me, I will clean it up a little before it is painted.
Ooops I thought you were the welder, I'll change my words to:
"Give a smart guy like you a phone to call a welder and the sky's the limit !"
REMEMBER: Keep it correct or you may face the
Nice work. Just something to think of with the trailer wider you may encounter issues when you turn a sharp corner or jack knife the trailer. My trailer is 82" between the fenders. I have add an extension on the hitch when I tow it behind the motor home to keep the front corners from contacting the bumper in a sharp turn.
Now you can load those cub's on sideways
Co- hosting Central Indiana Cub Fest near Tipton Indiana September of 2014
You got it Bob, Bill's a very talented man, when he has a phone in his hand. A welder, not so much! We're working on that, though. He has a nice machine, he just needs to get some practice with it.
As to Steve's comment, we don't want to see the rear corners of that new Silverado munched up. Hook it up and check it out, especially when backing.
Steve we took that into consideration befor starting. The tongue is long enough that we felt it would get into the bumper before the deck made contact with the truck. I hooked it up this morning in the -6º temps just to make sure.
Here the truck is not quite 90º.
There is about 12" to go before the tongue hit and the deck has plenty of clearance around the fender.
Wow, winter there. 28 degrees, this morning, here. Nice modification, on the trailer. Ed
50 ,52,53,56,59 F Cubs, 55,55,57,63,63 fast hitch, 64 lo-boys, 71 154, 184 lo-boy,61 cadet original. IH spreader,IH corn grinder, Oli. OC3 ,AC D10 ,IH 444 , Potato digger, wagner ldr 3 power units.
Who is online
Users browsing this forum: No registered users and 4 guests