Starter cranking amps

Farmall H, HV & Super H, 300 & 350, 1939-1958

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
User avatar
pokitisme
Cub Star
Cub Star
Posts: 73
Joined: Sat Oct 07, 2017 8:34 am
Zip Code: 64132
Skype Name: Pokitisme
Tractors Owned: 1948 international Harvester Farmall h
Location: Kansas City Missouri

Starter cranking amps

Postby pokitisme » Tue Oct 23, 2018 7:14 pm

I'm pretty sure I got a weak battery with dead cells. I'm almost 100% sure of it. What I'm curious about is with a voltmeter how do I determine the cranking amps for a starter on a 1948 Farmall h. Or does somebody have the actual listing for the amperage for the starter. I've charge this battery over and over and it reads 12 volts. But I suspect it's a pretty damn damage battery. I have not yet hooked up the voltmeter to it while I tried starting it I plan on doing that tomorrow. I checked all the connections and everything is pretty tight and I've cleaned everything when I hit the starter button it does attempt to turn just a little bit. but like I suspect I don't think it has enough volts to kick in. I know it's a screwed-up battery but the Curiosity part got the best of me so what is the starting and running amps for a 48 Farmall h
Favorite quotes by me. If you want to you can but if you don't you wont... most possibly yes but maybe no.... and as always buy guns keep America free

User avatar
John *.?-!.* cub owner
Team Cub Guide
Team Cub Guide
Posts: 22897
Joined: Sun Feb 02, 2003 2:09 pm
Zip Code: 63664
Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
Location: Mo, Potosi

Re: Starter cranking amps

Postby John *.?-!.* cub owner » Tue Oct 23, 2018 8:23 pm

I have never measured the cranking current on my old H, but typically on a 12 volt conversion you could expect 50 to 75 amps. The current drain will vary, rising as a piston comes up to TDC compressing the fuel air mix and drops off as it passes TDC, to repeat the cycle as the next piston comes up on TDC. Running current will be about .5 amp for the ignition, but I do not know what size alternator you installed when you converted to 12 volts. You cannot measure cranking current with a typical multimeter, you will either need an inline ammeter capable of handling that type current, or a clamp on DC meter.

Read voltage directly across battery, and then with lights on if you have them. See if it holds 12 volts. Then with lights off, read battery voltage while cranking. with a 12 volt system it should stay above 8 volts. Having a 12 volt system powering a 6 volt starter can make readings unusual though.
If you are not part of the solution,
you are part of the problem!!!

tst
5+ Years
5+ Years
Posts: 2977
Joined: Tue Jan 12, 2010 2:08 pm
Zip Code: 12514
Circle of Safety: Y

Re: Starter cranking amps

Postby tst » Tue Oct 23, 2018 8:48 pm

a fully charged 12v battery should rear 13 to 13-5 volts so your battery is not fully charged or could have a bad cell, on a volt meter while cranking the engine it shout not drop down to less than 9 volts, a battery with low voltage will kill a starter if you continue to use it long enough

User avatar
pokitisme
Cub Star
Cub Star
Posts: 73
Joined: Sat Oct 07, 2017 8:34 am
Zip Code: 64132
Skype Name: Pokitisme
Tractors Owned: 1948 international Harvester Farmall h
Location: Kansas City Missouri

Re: Starter cranking amps

Postby pokitisme » Wed Nov 28, 2018 7:01 am

Too much guys. Yeah the point about the alternator is a good point because not everybody switches over to 12 volt with the same alternator. Which I had not considered. You know what really sucks about this is I had videos up on YouTube showing me starting the tractor with the voltmeter attached reading the actual voltage and stupid YouTube deleted my page I do have a second page but it only has like 4 videos up I think it does have a complete carburetor tear down and rebuild on it. Anyway guys thanks much for your info
Favorite quotes by me. If you want to you can but if you don't you wont... most possibly yes but maybe no.... and as always buy guns keep America free

User avatar
ShawnAgne
Cub Star!!
Cub Star!!
Posts: 494
Joined: Sat May 07, 2016 5:13 pm
Zip Code: 45380
Tractors Owned: 1952 Cub w/ 184 motor (Kid)
12V with Petronix
IH 3160 Mower Deck
54 Leveling Blade
193 Plow
IH528 Trailer
Farmall 300 (Clarence)
12V with Petronix
Woods L306 72"
Circle of Safety: Y
Location: Versailles, Ohio

Re: Starter cranking amps

Postby ShawnAgne » Fri Dec 07, 2018 9:26 pm

When I converted the 300 and the Cub over to 12V with electronic ignition about a year ago I just got the biggest battery that would fit in the Cub box and used that in the 300 also. It doesn't take much as the 12V battery will spin the 6V starter pretty fast. Prior to conversion I had a cell go bad on a new battery I bought for the Cub, they won't start. However if I remember correctly it never read 6V, it only read around 4.5V.
Shawn Agne


  • Similar Topics
    Replies
    Views
    Last post

Return to “Farmall H, HV, Super H, 300 & 350”

Who is online

Users browsing this forum: No registered users and 0 guests