Wanted: hydraulic line for 1650 front plow quick connect

For sale, wanted and vine forum. All ads are free and run for a minimum of 21 days.
Disclaimer: All transactions are between the buyer and the seller. Farmallcub.com, it's administrator, moderators, guides and mentors accept no responsibility for your personal transactions. Always use caution when dealing with known and unknown individuals on the internet. Issues/disputes between the buyer and the seller are to be handled via phone, email, mail, etc. and not on the public forums.

Moderator: Team Cub

Forum rules
IMPORTANT: Rules for selling/buying are found here (section 5): Rules
Tom Evans
10+ Years
10+ Years
Posts: 130
Joined: Fri Jul 02, 2004 7:12 pm
Zip Code: 49032
Location: Centreville, MI. 49032

Wanted: hydraulic line for 1650 front plow quick connect

Postby Tom Evans » Wed Jun 13, 2018 12:25 pm

Looking for the steel upper hydraulic line that runs from the pump to the front quick connector used for the snow plow. I believe it's IH-106877-C1. This is for my 1975 1650 Cub Cadet. Thanks, Tom. Centreville, MI.

User avatar
gitractorman
10+ Years
10+ Years
Posts: 2590
Joined: Mon Oct 24, 2005 11:35 am
Zip Code: 14072
eBay ID: toysforjake
Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel
Circle of Safety: Y
Location: Grand Island, NY

Re: Wanted: hydraulic line for 1650 front plow quick connect

Postby gitractorman » Thu Jun 14, 2018 1:05 pm

Tom,
I doubt you'll find that line. It's just not a common problem item, and I've never seen one replaced. I would suggest getting one made up.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller

User avatar
BIGHOSS
10+ Years
10+ Years
Posts: 1656
Joined: Tue Jul 18, 2006 9:55 pm
Zip Code: 37087
Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower

1974 Cub S/N 244814
w/59 Woods Mower

Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog

and a Palomino Mare named GIGI
Circle of Safety: Y
Location: TN, Lebanon

Re: Wanted: hydraulic line for 1650 front plow quick connect

Postby BIGHOSS » Thu Jun 14, 2018 3:25 pm

Don't know about your situation, but I had a similar issue with my Ford 3000 at few weeks ago. The 1/2" steel pressure line started leaking near the pump in a bend in the line. I took the line to a local hydraulic specialty shop. They cut the steel line in half and installed a rubber hose to the good half with the correct fitting on the pump end. I installed the steel end back to the tractor housing and the rubber end to the pump. Problem solved!
Don't know if this would work for you or not.
"Courage is being scared to death-but saddling up anyway".......John Wayne

Tom Evans
10+ Years
10+ Years
Posts: 130
Joined: Fri Jul 02, 2004 7:12 pm
Zip Code: 49032
Location: Centreville, MI. 49032

Re: Wanted: hydraulic line for 1650 front plow quick connect

Postby Tom Evans » Fri Jun 15, 2018 6:48 am

I was at the J D dealer yesterday and picked up a plug to cap the line at the pump. They make rubber hydraulic lines there. I'm thinking I might have them make me up a line and just figure out a bracket to hold the hydraulic quick connect at he front. I'll probably leave this add out there, just in case someone comes up with a steel line. Thanks for the advice. Tom

User avatar
gitractorman
10+ Years
10+ Years
Posts: 2590
Joined: Mon Oct 24, 2005 11:35 am
Zip Code: 14072
eBay ID: toysforjake
Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel
Circle of Safety: Y
Location: Grand Island, NY

Re: Wanted: hydraulic line for 1650 front plow quick connect

Postby gitractorman » Mon Jun 18, 2018 12:46 pm

They make the hydraulic quick connects that are "bulkhead fittings", which means they have a separate nut on the back so that they will bolt into a piece of steel or sheet metal. Yours should be that way already, but the backing nuts are often spun off onto the hydraulic line, and just hanging somewhere on the line. If they're installed correctly, a rubber line should be fine.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller


Return to “The VINE”

Who is online

Users browsing this forum: butchs38, radioguy41 and 1 guest