This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
1955 cub wiring
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 160
- Joined: Wed Aug 07, 2013 10:09 am
- Zip Code: 14103
- Tractors Owned: 1955 farmall cub w/ fast hitch
Implements:
fast hitch moldboard plow
fast hitch disc harrow
front blade
Danco c-3 mower - Circle of Safety: Y
1955 cub wiring
Hey guys, I'm about to replace the wiring in my cub FINALLY, so i've been reading up on the subject here. One thing that i can't quite figure out is whether or not my tractor is supposed to be positive or negative ground. Right now it's hooked up with negative ground and it runs OK, but the battery doesn't charge. of course, by the state of the wiring, there could definitely be something else causing that. The ammeter doesn't move at all.. ever. the wires for the lights are in varying stages of decay/missing, and I think someone bypassed the fuse holder... I've never done any vehicle wiring before, so forgive me if i'm asking stupid questions.. I'm just planning on replacing the wires one at a time so i know i'm not missing anything.
-
- 10+ Years
- Posts: 5212
- Joined: Tue Jan 12, 2010 2:08 pm
- Zip Code: 12514
- Circle of Safety: Y
Re: 1955 cub wiring
All cubs with 6 volt system are positive ground
- Jack
- 10+ Years
- Posts: 836
- Joined: Sun Aug 14, 2005 11:14 am
- Zip Code: 16353
- Tractors Owned: 1955 Farmall Cub
1955 International 300 Utility
2018 JD loader/ backhoe - Circle of Safety: Y
- Location: Tionesta, PA.
Re: 1955 cub wiring
Eoghan, there are not any stupid questions. if you don't know, and don't ask, how will you ever find out the answers
Pine Meadows Farm
- BIGHOSS
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: 1955 cub wiring
I recommend that you get a complete wiring harness from John Brillman http://brillman.com/store/a-tractor/wire-harnesses.html. It will be correct with original type wire, terminals and length. I wired mine using a Brillman harness in about and hour. As a guide, I used a wiring diagram for my year cub, what was left of original wiring and instructions from Brillman. It was around $100, which was money well spent.
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- 10+ Years
- Posts: 160
- Joined: Wed Aug 07, 2013 10:09 am
- Zip Code: 14103
- Tractors Owned: 1955 farmall cub w/ fast hitch
Implements:
fast hitch moldboard plow
fast hitch disc harrow
front blade
Danco c-3 mower - Circle of Safety: Y
Re: 1955 cub wiring
excellent, thanks guys!
BigHoss, that harness looks beautiful! i think maybe too beautiful for the dirty work she'll be doing.. i'd consider buying one if there was a less expensive (not braided cotton) version. I'm pretty sure i could make my own if i could decipher the wiring diagram.. maybe not.
BigHoss, that harness looks beautiful! i think maybe too beautiful for the dirty work she'll be doing.. i'd consider buying one if there was a less expensive (not braided cotton) version. I'm pretty sure i could make my own if i could decipher the wiring diagram.. maybe not.
- twotone
- 10+ Years
- Posts: 1189
- Joined: Sat May 14, 2011 6:09 pm
- Zip Code: 15132
- Tractors Owned: 53 F Cub
73 F Cub
53 Super A With Snow/Grader Blade
193 Plow With Colter And Jointer
144 Cultivators
22 Mower - Circle of Safety: Y
- Location: Versailles,Pa.
Re: 1955 cub wiring
I made my own, but my original harness was not all cut up, so fairly easy to copy. It took me the better part of a day to make, but crimp, solder, shrink tube every terminal is time consuming, especially when you forget to put shrink tube on the wire before you solder the connector!
Know Your Cub, And Your Cub Will Know You.
Tom
Tom
-
- 10+ Years
- Posts: 2929
- Joined: Sun Apr 19, 2009 9:51 pm
- Zip Code: 63664
- Location: MO, Potosi
Re: 1955 cub wiring
Making your own is not all that difficult, especially if you're just going for functional. It doesn't have to be a harness. Just run the wires from point a to point b following where the originals were. When you're done you can tape or wire tie them into a bundle. As for deciphering the wiring harness really isn't much to it once you figure out what you have. Still have a generator? Magneto or distributor? Regulator or cutout? Which headlight switch? Fuse on dash or back of headlight switch? (If it's a late Cub then you get into 12V and key switches and all that, but a lot fewer of those)
This is a good time to stress good clean connections. A wire brush, sandpaper, and emory cloth are good to have handy to clean up the connections before you put the wire on. A little dielectric grease won't hurt either. If you can do a good strip and crimp on the wire then you should be fine.
With the battery unhooked I would start at the starter and put a big ring terminal on the end of a wire that would fit over the stud. The other end of that wire goes to the ammeter, so stretch out enough wire to reach the ammeter and give yourself some extra in case you have to redo a terminal now or ten years from now and put on the terminal and make the connection. Since you're at the ammeter put a terminal on the end of another wire and connect it up to the other side of the ammeter. That wire most likely will run to the regulator "bat" terminal so run it up under the gas tank down the right side of the Cub and up to the regulator, leave a little extra, add terminal, shine it up, add dielectric grease, make connection. You just keep going like that.
This is a good time to stress good clean connections. A wire brush, sandpaper, and emory cloth are good to have handy to clean up the connections before you put the wire on. A little dielectric grease won't hurt either. If you can do a good strip and crimp on the wire then you should be fine.
With the battery unhooked I would start at the starter and put a big ring terminal on the end of a wire that would fit over the stud. The other end of that wire goes to the ammeter, so stretch out enough wire to reach the ammeter and give yourself some extra in case you have to redo a terminal now or ten years from now and put on the terminal and make the connection. Since you're at the ammeter put a terminal on the end of another wire and connect it up to the other side of the ammeter. That wire most likely will run to the regulator "bat" terminal so run it up under the gas tank down the right side of the Cub and up to the regulator, leave a little extra, add terminal, shine it up, add dielectric grease, make connection. You just keep going like that.
-
- 10+ Years
- Posts: 347
- Joined: Wed Mar 06, 2013 12:20 pm
- Zip Code: 20164
- Tractors Owned: 1951 Farmall cub
- Contact:
Re: 1955 cub wiring
I got mine from a company called Brillmans. They were braided and color coded with diagram. I think I paid $100.
- BIGHOSS
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: 1955 cub wiring
Disclaimer: "No, I do not work for Brillman, Porch or any other vendors that make and sell wiring harnesses". I have been called frugal, even cheap by the ones who know me. So, I do not spend money when it is not justified. I am retired and probably have the time to make up wires for a cub. I was an industrial and manufacturing engineer in my other life. So, I love fixing things and making them work. That being said, $100 to me is a good investment for a complete wiring harness that is easy to install and works %100 from the get go. JMHO.
"Courage is being scared to death-but saddling up anyway".......John Wayne
- clodhopper
- 10+ Years
- Posts: 807
- Joined: Sat May 07, 2011 8:20 pm
- Zip Code: 27526
- Tractors Owned: 1950 Cub Demo
1978 Cub Cadet 1650
cub 193 plow
cub 174 planter
cub sidedresser
cub 144 cultivator
cadet 50C deck - Circle of Safety: Y
Re: 1955 cub wiring
First I would say if you don't have a basic understanding of simple automotive wiring then my recommendation is a prefabricated harness from whomever. If you are comfortable with building your own then I would go that route. I built my own and saved quite a bit.
Who is online
Users browsing this forum: No registered users and 52 guests