Helping my neighbor replace the mower blade clutch on a 757 JD (Did I say that out loud). This is a $300+ clutch assembly. We finally got the old one off by using a 3 jaw pulley and taking our time. It was really tight. The problem is how to install the new assy without damaging it. There are two problems. One is how to align the the key to the keyway in the shaft. The new assy will have to be pressed on about an inch or more before touching the key. Then it is too late to clock the clutch in case the key and keyway do not line up. Which will happen, because you are trying to align it blind. Then there is the problem of how to press the clutch assy on to the shaft. The 7/16 fine thread bolt is too short to start pulling it on to the shaft. How do you heat the clutch assy, since it has sealed bearings and a electo magnet?
Anyone out there ran into this problem?
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Electric mower blade clutch
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Electric mower blade clutch
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- 10+ Years
- Posts: 505
- Joined: Fri May 05, 2006 12:00 am
- Zip Code: 54515
- Circle of Safety: Y
- Location: WI, Catawba
Re: Electric mower blade clutch
Unless because it's a bigger machine I don't know why you would need to press it back on. Was it rusted on? I've done our F525, Lx186, and a Lawn Boy GT18 H, and I didn't need a puller on any of them to get the clutch off. With a little cleaning they all slid right back on, in fact the JD's hanging down were hard to hold up while trying to get the bolt started. If you have to press it on why not just start with a longer bolt. Make sure it has plenty of threads started before torquing down on it. If I remember right on ours you can have the key part way out in order to line it up.
Mark "birddog" Birdeau
![Circle of Safety](../safetyquiz/cos_avatar.png)
![Circle of Safety](../safetyquiz/cos_avatar.png)
-
- 10+ Years
- Posts: 523
- Joined: Fri Feb 11, 2011 6:06 pm
- Zip Code: 62995
- Tractors Owned: 1951 Farmall Cub
1950 John Deere A
1949 Farmall Cub
1943 Farmall H
1940 Farmall H
1953 Farmall Super M
1962 Massey Ferguson 65 - Circle of Safety: Y
- Location: Southern Illinois
Re: Electric mower blade clutch
Clutch should just pull off ( yes I know ). Just remove any rust on the shaft with some emery cloth and then put anti-seize on the shaft. It should slide right back on with out to much trouble.
If not use some military words on it, that works for me
Rodney![Cool 8)](./images/smilies/icon_cool.gif)
If not use some military words on it, that works for me
![Laughing :lol:](./images/smilies/icon_lol.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
Rodney
![Cool 8)](./images/smilies/icon_cool.gif)
USAF 1976 - 1996
-
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: Electric mower blade clutch
We must not be looking at the same type machine. This is the big commercial type zero turn 757 with a 25 hp motor. Nothing was rusted, just a press fit. The 3 jaw puller strained all the way. The clutch is installed on the rear of the crankshaft. The smaller JDs with a vertical engine has one similar to this one. But they are made in two pieces. An inner sleeve that you can line up to the keyway in the shaft easier. Then the clutch assy slides over this sleeve. I don't see how this one comes apart.
Looks like this one. http://www.amazon.com/John-Deere-Clutch ... B008J4VMS8
Especially the one priced at $147.
Looks like this one. http://www.amazon.com/John-Deere-Clutch ... B008J4VMS8
Especially the one priced at $147.
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- 10+ Years
- Posts: 523
- Joined: Fri Feb 11, 2011 6:06 pm
- Zip Code: 62995
- Tractors Owned: 1951 Farmall Cub
1950 John Deere A
1949 Farmall Cub
1943 Farmall H
1940 Farmall H
1953 Farmall Super M
1962 Massey Ferguson 65 - Circle of Safety: Y
- Location: Southern Illinois
Re: Electric mower blade clutch
According to the JD parts web site you need either a TCA12522 or TCA 15800 clutch depending on serial number of the mower. The clutch probably will not have these numbers on them but will have a Ogura or Warner number on it. I don't have my cross reverence book at home. Just a guess, some one may have put the wrong clutch on it before you got a hold of it. Of all the mowers and electric clutches I have worked on I have never had to press one on.
Rodney![Cool 8)](./images/smilies/icon_cool.gif)
Rodney
![Cool 8)](./images/smilies/icon_cool.gif)
USAF 1976 - 1996
-
- Cub Pro
- Posts: 1741
- Joined: Tue Jul 18, 2006 9:55 pm
- Zip Code: 37087
- Tractors Owned: 1947 Cub S/N 9216
w/ C-22 Mower
1974 Cub S/N 244814
w/59 Woods Mower
Ford 3000 Gas S/N C375091 w/Bushhog QT2345 Loader & 6' Squealer Bushhog
and a Palomino Mare named GIGI - Circle of Safety: Y
- Location: TN, Lebanon
Re: Electric mower blade clutch
I was gone most of yesterday, but when I got home late I saw that his grass had been cut. Looks like he got the new one on. Thanks for your advice.
"Courage is being scared to death-but saddling up anyway".......John Wayne
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 391
-
by Stanton
Sat Jun 05, 2021 7:16 am
-
- 3
- 555
-
by FarmallAddict
Fri Oct 15, 2021 10:47 am
-
-
Mott Flail Mower on Cub Attachment(s)
by FarmallCub14660 » Wed Jun 21, 2023 7:41 pm » in Other Tractors and Machinery - 5
- 1271
-
by Eugene
Thu Jun 22, 2023 9:12 am
-
-
- 2
- 182
-
by v w
Sat Sep 17, 2022 7:45 pm
-
-
NH 451 Sickle mower leg dimensions Attachment(s)
by Poncho » Fri Aug 13, 2021 9:05 pm » in Other Tractors and Machinery - 8
- 677
-
by Poncho
Sat May 28, 2022 9:36 pm
-
Return to “Other Tractors and Machinery”
Who is online
Users browsing this forum: No registered users and 3 guests