This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Cubradiator overflow tube
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 6
- Joined: Tue May 17, 2011 8:24 am
- Zip Code: 48866
- Tractors Owned: 1964 Massey Ferguson 65
1953 Farmall Cub
Cubradiator overflow tube
Does the whole hood have to come off, fuel tank and all, to get to radiator overflow tube? There is a hole in it spewing coolant all over. Is there an easy way to get it off?
-
- Team Cub
- Posts: 11851
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Cubradiator overflow tube
The top of the overflow tube is soldered into the back of the radiator neck. The bottom goes through a hole in a clip that is fastened to one of the rear radiator bolts. You will need to remove the hood and gas tank. However, if you have recently added coolant, you may just have excess draining out. I have several Cubs without the tubes, and any excess coolant is dispersed by the fan instead of dripping out the bottom of the tube. These Cubs are not trailer queens so I am not concerned about a little antifreeze on the hood or elsewhere.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
- Bus Driver
- 10+ Years
- Posts: 2917
- Joined: Sat Feb 11, 2006 5:26 pm
- Location: NC
Re: Cubradiator overflow tube
The experience of others may vary, but the only repair that has worked for me is to remove the radiator and take it to a radiator repair shop. Lots of stuff to remove. Be advised that the coolant level for a cub is proper only within a narrow range. Too much and it will overflow as the coolant warms and expands, too little and the coolant will not circulate at all. No circulation and the cub will overheat to the point of engine damage.
Luck favors those who are prepared
-
- 10+ Years
- Posts: 6
- Joined: Tue May 17, 2011 8:24 am
- Zip Code: 48866
- Tractors Owned: 1964 Massey Ferguson 65
1953 Farmall Cub
Re: Cubradiator overflow tube
I can see the tube near the radiator cap. Right at the bend it has a hole. That's where the coolant is coming out. Is that a problem, or just a nuisance?
- Denny Clayton
- 10+ Years
- Posts: 4565
- Joined: Wed Feb 05, 2003 1:18 pm
- Zip Code: 45365
- Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
- Circle of Safety: Y
- Location: OH, Sidney
Re: Cubradiator overflow tube
glinka wrote:I can see the tube near the radiator cap. Right at the bend it has a hole. That's where the coolant is coming out. Is that a problem, or just a nuisance?
Let it spew for a while. Once it reaches the proper level it should quit.
-
- Team Cub
- Posts: 11851
- Joined: Tue May 25, 2004 8:02 pm
- Zip Code: 80501
- Tractors Owned: Cubs, MH Pony, Shaw, Allis G, 1934 Silver King, JD LA and LI, Gibson D, David Bradley Tri-Trac
- Circle of Safety: Y
- Location: CO, Longmont
Re: Cubradiator overflow tube
If you have enough access to the hole, you could put a dab of solder on it or even JB Weld.
Bob
Bob
"We don't need to think more,
we need to think differently."
-Albert Einstein
we need to think differently."
-Albert Einstein
Who is online
Users browsing this forum: dgrapes59 and 22 guests