OK, what did I not do correctly This was my first use of a gravity feed compressed air paint gun and with these results, there may just be a sale on a lot of unpainted metal parts Your suggestions are most welcome. Parts had been treated with phosphoric acid soln to inhibit rust after E Tanking.
Used an acrylic lacquer primer with lacquer thinner at recommended mixing ratio.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Something is VERY wrong!!
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 3034
- Joined: Wed May 31, 2006 12:09 pm
- Zip Code: 74070
- Circle of Safety: Y
- Location: OK, Skiatook
-
- 10+ Years
- Posts: 1573
- Joined: Sun Feb 02, 2003 11:01 pm
- Zip Code: 36310
- Tractors Owned: 1975 IH cub,1948 farmall cub,1979 international 3200 skid steer and a 1974 John deere 350B dozer.
- Location: Abbeville Alabama
Re: Something is VERY wrong!!
When painting bare metal it should be coated with a etching primer, then your regualar prime rover that.. Usesing many thin coats. After the primer cures then you can top coat. But depending on weather and paint you may heve to use a slow reducer. especially when its hot a humid. From your pictures it looks to me like the paint and or both paint and primers dried way too fast causing the pealing.
Collector of Farmall cubs and cub cadets.Injoy helping people keep their cubs running. Years of experipnce.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Something is VERY wrong!!
Bill:
What was the temperature and the ambient humidity? That is important. But more important is a good primer base. Usually a thin first coat of etch, then a thin hi-bild primer coat lightly sand, a second thin coat .. lightly sand then the top coats. As Clark said, a number of thin coats are better than a thick coat. It appears that 2 things are happening here. No etching primer and too much primer coming out of the gun. Turn down the proper adjustment screw on the gun that controls the product feed rate. Also, make sure that your air pattern is correct.
What was the temperature and the ambient humidity? That is important. But more important is a good primer base. Usually a thin first coat of etch, then a thin hi-bild primer coat lightly sand, a second thin coat .. lightly sand then the top coats. As Clark said, a number of thin coats are better than a thick coat. It appears that 2 things are happening here. No etching primer and too much primer coming out of the gun. Turn down the proper adjustment screw on the gun that controls the product feed rate. Also, make sure that your air pattern is correct.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 3034
- Joined: Wed May 31, 2006 12:09 pm
- Zip Code: 74070
- Circle of Safety: Y
- Location: OK, Skiatook
Re: Something is VERY wrong!!
Rudi wrote:Bill:
What was the temperature and the ambient humidity? That is important. But more important is a good primer base. Usually a thin first coat of etch, then a thin hi-bild primer coat lightly sand, a second thin coat .. lightly sand then the top coats. As Clark said, a number of thin coats are better than a thick coat. It appears that 2 things are happening here. No etching primer and too much primer coming out of the gun. Turn down the proper adjustment screw on the gun that controls the product feed rate. Also, make sure that your air pattern is correct.
Thanks Rudi Temp 77 F Humidity 52% used acrylic lacquer primer thinned with lacquer thinner. These parts have been sitting around for 3+ years with a phosphoric acid type coating for rust inhibition. (which is supposed to provide proper etching)
They were rinsed and dried before painting. During painting, noticed the flaking, so wiped the piece down with thinner and started over--same results. Parts shown above are forged steel pieces of Univ. Mounting frame, did notice the cast pieces of the frames also wanted to flake. Have since used liquid soap and water with SS scrubber to remove all remaining paint and hopefully rough up the metal a bit.
Don't know if that was the problem, or as you said, too much paint, wrong thinner, not enough flash between coats........and so on--So many variables Will stay with it and see if I can figure out the problem. Further suggestions solicited Got 4+ inches rain yesterday, so painting will be on hold till humidity drops--current 70-90%
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Re: Something is VERY wrong!!
I would say the parts were dirty. Etch is nice for clean sheet metal but I am not sure it adds anything on sanded or rusted metal. The phosphoric acid already etched the metal if any was needed. From the photos looks like the paint did not stick and I would guess the metal was dirty from something. The problem with phosphoric acid is it will etch deeply and leave dirt and other nasty things in those deep etch pockets.
I never use etching primer since nothing I paint is untouched metal. It has been sanded, derusted, etc....
Does not hurt to use etching primer but the lack of etching primer was not the problem in this case.
I never use etching primer since nothing I paint is untouched metal. It has been sanded, derusted, etc....
Does not hurt to use etching primer but the lack of etching primer was not the problem in this case.
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Something is VERY wrong!!
Bill:
Yup, wait until the humidity and temp is down to what the manufacturer stipulates for your particular product. Pay attention to what they recommend for surface prep, primer, wait times and of course top coats.
Etch is not required .. it is just what I have been using when my parts come out of the tank -- I use etching primer then hi-bild primer. A good primer is required though. Practice, practice and more practice will help with ironing out issues when painting.
Keep us posted on your progress ..
Yup, wait until the humidity and temp is down to what the manufacturer stipulates for your particular product. Pay attention to what they recommend for surface prep, primer, wait times and of course top coats.
Etch is not required .. it is just what I have been using when my parts come out of the tank -- I use etching primer then hi-bild primer. A good primer is required though. Practice, practice and more practice will help with ironing out issues when painting.
Keep us posted on your progress ..
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
-
- 10+ Years
- Posts: 3034
- Joined: Wed May 31, 2006 12:09 pm
- Zip Code: 74070
- Circle of Safety: Y
- Location: OK, Skiatook
Re: Something is VERY wrong!!
Thanks for the information gentlemen. After considerable research, I'm down to the following variables:
Air/paint ratio
coating thickness
flash time
precleaning parts
So, I will find some scrap and practice, practice,practice Have also learned acrylic lacquer primer tends to shrink during drying process, so will give primed parts plenty of cure time before top coat. Since I have $$ tied up in the primer, will use it for implements/tractor castings and reserve the epoxy primer for the sheet metal. Pics as I progress--right now in rainy period with high heat and humidity so will be on hold.
Not too many good painting days in Ok.
Air/paint ratio
coating thickness
flash time
precleaning parts
So, I will find some scrap and practice, practice,practice Have also learned acrylic lacquer primer tends to shrink during drying process, so will give primed parts plenty of cure time before top coat. Since I have $$ tied up in the primer, will use it for implements/tractor castings and reserve the epoxy primer for the sheet metal. Pics as I progress--right now in rainy period with high heat and humidity so will be on hold.
Not too many good painting days in Ok.
Who is online
Users browsing this forum: Dave Downs, Flemmingth and 56 guests