This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Rough Idle/Backfire
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- AgTires4295
- 10+ Years
- Posts: 197
- Joined: Fri Dec 30, 2011 7:36 pm
- Zip Code: 20646
- Tractors Owned: 1940 Farmall A
1947 Farmall H
1951 Farmall Cub
1970 Cub Cadet 127
1970 Simplicity Broadmoor 728 (x2)
1984 Cub Cadet 782
1964 Simplicity Landlord
2014 Simplicity Broadmoor 23/50 - Location: La Plata, MD
Re: Rough Idle/Backfire
Alrighty Cub Fam, I had off tonight and was able to get to the Cub. I worked the timing to get it perfect (perfect in that it purrs like a kitten, idles low and fires up immediately on a cold start). So, success in getting it running!! I was pretty happy until I started to drive it and it went from a healthy high idle to a bog and died... in first gear, up hill. So it hit me that maybe I fouled the plugs in running Seafoam through the intake and gas. I replaced the spark plugs with all new. Fired it up, hoping for improvement and nadda... same symptoms: great idle from the lowest to the highest rev. Placed in gear, bogs while driving up hill and dies.
So yeah I know, I havent gotten around to the compression testing and havent even considered adjusting the valve springs yet. Before I go out and drop anymore money from my severly taxed public service paycheck, does anybody have anymore ideas?
It kills me that its running GREAT but low on power when it is confronted with any sort of load (PTO included).
So yeah I know, I havent gotten around to the compression testing and havent even considered adjusting the valve springs yet. Before I go out and drop anymore money from my severly taxed public service paycheck, does anybody have anymore ideas?
It kills me that its running GREAT but low on power when it is confronted with any sort of load (PTO included).
- RaymondDurban
- Cub Pro
- Posts: 4435
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: Rough Idle/Backfire
Being that the tractor hasn't run in some time, it may take a bit for the Seafoam to loosen the rings to bring the compression up. I'd definitely try to adjust the valves. If they are out if adjustment, it may help a lot with the low power.
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Rough Idle/Backfire
I agree with Raymond ... sounds like a good plan. Take the valve cover gasket off and roll the engine over by hand. It will soon be apparent which valves may be stuck/sticking. Adjust the valve lash. Should show good improvement. The Sea Foam will help a lot with the carbon buildup.
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
- Hengy
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
- Contact:
Re: Rough Idle/Backfire
When it is running rough under load, does it run any better if you pull the choke slightly? Did you ever check and clean the main jet on the side of the carb?
Mike
Mike
- AgTires4295
- 10+ Years
- Posts: 197
- Joined: Fri Dec 30, 2011 7:36 pm
- Zip Code: 20646
- Tractors Owned: 1940 Farmall A
1947 Farmall H
1951 Farmall Cub
1970 Cub Cadet 127
1970 Simplicity Broadmoor 728 (x2)
1984 Cub Cadet 782
1964 Simplicity Landlord
2014 Simplicity Broadmoor 23/50 - Location: La Plata, MD
Re: Rough Idle/Backfire
I love all of this great input. Ill have to pull the valve cover off next chance I get and see whats what. I have been through the carb several times. In and out that thing is cleaner than when it rolled off of the assembly line
I was hoping it was a carb issue but nope. Its not apparent that it is although the symptoms scream "carb!" I will say this, the exhaust is blowing cleaner and Hell-HOT since I Seafoamed it. I hope I didnt screw something up by possibly using too much.
![Smile :)](./images/smilies/icon_smile.gif)
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Rough Idle/Backfire
After I put Sea Foam in Ellie and ran it for a while I noticed an improvement in the idle and when picking up rpms. After a bit, I put my hand over the exhaust (no muffler just a straight pipe) and she was just a purrin .. you could feel the smoothness and the exhaust got hotter as time went on. I think this is a good thing - as the carbon gets cleaned out the engine is bound to perform better and with better performance comes an increase in heat.
At least that is how I figure it. Mind you I am an amateur wrench banger here and I leave much of the mechanical to the real wrench turners![Laughing :lol:](./images/smilies/icon_lol.gif)
If you put in too much Sea Foam in the gas the only thing that will happen is that it will smoke more until you empty the tank or dilute the Sea Foam with more gas. I don't think it will do much more in the crankcase. As it cleans, there is less carbon to burn up hence less smoke.
You may be pleasantly surprised after you adjust the valve lash.
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/Valve%20Lash%20Adjusting%20Procedure.jpg)
At least that is how I figure it. Mind you I am an amateur wrench banger here and I leave much of the mechanical to the real wrench turners
![Laughing :lol:](./images/smilies/icon_lol.gif)
If you put in too much Sea Foam in the gas the only thing that will happen is that it will smoke more until you empty the tank or dilute the Sea Foam with more gas. I don't think it will do much more in the crankcase. As it cleans, there is less carbon to burn up hence less smoke.
You may be pleasantly surprised after you adjust the valve lash.
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/Valve%20Lash%20Adjusting%20Procedure.jpg)
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
- AgTires4295
- 10+ Years
- Posts: 197
- Joined: Fri Dec 30, 2011 7:36 pm
- Zip Code: 20646
- Tractors Owned: 1940 Farmall A
1947 Farmall H
1951 Farmall Cub
1970 Cub Cadet 127
1970 Simplicity Broadmoor 728 (x2)
1984 Cub Cadet 782
1964 Simplicity Landlord
2014 Simplicity Broadmoor 23/50 - Location: La Plata, MD
Re: Rough Idle/Backfire
Im tracking with ya Rudi
With your chart that you posted, I am 99% sure I understand what it advises to do BUT how do you know how much to adjust or not?
Thanks again!
![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
Thanks again!
- RaymondDurban
- Cub Pro
- Posts: 4435
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: Rough Idle/Backfire
Adjust the valves to .014"
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: Rough Idle/Backfire
As Raymond said, 0.014 or 0.015 is about right .. I think mine I did at 0.014". Manual says 0.013" cold but on an older engine a little bit more is ok.
GSS-1007 Engine
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/GSS-1007%20Engine/Page%2015.jpg)
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/GSS-1007%20Engine/Page%2016.jpg)
GSS-1007 Engine
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/GSS-1007%20Engine/Page%2015.jpg)
![Image](http://www.cleancomputes.com/Cub/Blue%20Ribbon%20Service%20Manuals/GSS-1007%20Engine/Page%2016.jpg)
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
- AgTires4295
- 10+ Years
- Posts: 197
- Joined: Fri Dec 30, 2011 7:36 pm
- Zip Code: 20646
- Tractors Owned: 1940 Farmall A
1947 Farmall H
1951 Farmall Cub
1970 Cub Cadet 127
1970 Simplicity Broadmoor 728 (x2)
1984 Cub Cadet 782
1964 Simplicity Landlord
2014 Simplicity Broadmoor 23/50 - Location: La Plata, MD
Re: Rough Idle/Backfire
Thanks for the great info! I looked at maybe doing the valves today but figured it looked like something that would definitely take more time than I had. I did run the Cub around for a little bit and made a vid: https://www.youtube.com/watch?v=C3HFwv- ... ata_player
There's no new info here outside of what yall already know. I made it as a last hope before I try to adjust the valves in that maybe somebody can see something that hasnt been described previously. Either way, its a Cub vid so enjoy![Very Happy :D](./images/smilies/icon_biggrin.gif)
There's no new info here outside of what yall already know. I made it as a last hope before I try to adjust the valves in that maybe somebody can see something that hasnt been described previously. Either way, its a Cub vid so enjoy
![Very Happy :D](./images/smilies/icon_biggrin.gif)
-
- Team Cub
- Posts: 17278
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Rough Idle/Backfire
OK, check the valve adjustments. It probably needs it and certainly can't hurt. But here are the 2 things I would be checking:
1) Timing. Recheck static timing to fire exactly at TDC. Then use a timing light to make sure it advances to the advance mark (16 degrees) at fast idle. It it isn't advancing, you have some work to do in the distributor.
2) Make sure the governor is responding. When you reach that hill, the governor should pop the throttle fully open. If it doesn't, you may have a binding or mis-adjusted linkage from the governor to the carburetor. If that is good and it still doesn't respond, you have trouble inside the governor. You should be able to search for governor linkage to find details on the adjustment.
1) Timing. Recheck static timing to fire exactly at TDC. Then use a timing light to make sure it advances to the advance mark (16 degrees) at fast idle. It it isn't advancing, you have some work to do in the distributor.
2) Make sure the governor is responding. When you reach that hill, the governor should pop the throttle fully open. If it doesn't, you may have a binding or mis-adjusted linkage from the governor to the carburetor. If that is good and it still doesn't respond, you have trouble inside the governor. You should be able to search for governor linkage to find details on the adjustment.
- Rick Spivey
- Cub Pro
- Posts: 2779
- Joined: Sun Jul 01, 2007 10:07 pm
- Zip Code: 29518
- Circle of Safety: Y
- Location: SC, Cades 29518
Re: Rough Idle/Backfire
I couldn't listen to the whole video, but I caught a fair amount of it. I don't think your idle is actually all that smooth, there were times when I wondered if you were running on only two cylinders. As it started up the hill, it sounded more like it was running on all 4, but not with any "oomph". So I have two suggestions:
1) check that your wires are in the right firing order, let's be sure we have all 4 cylinders contributing - 1342, 1 closest to radiator, and at approximately 12:00 on distributor cap
2) I still wonder if your coil isn't breaking down; is it magneto or battery ignition, and if magneto, internal or external coil? I re-read the post, but didn't see the answer to this question.
1) check that your wires are in the right firing order, let's be sure we have all 4 cylinders contributing - 1342, 1 closest to radiator, and at approximately 12:00 on distributor cap
2) I still wonder if your coil isn't breaking down; is it magneto or battery ignition, and if magneto, internal or external coil? I re-read the post, but didn't see the answer to this question.
Rick Spivey
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
-
- Team Cub
- Posts: 17278
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Rough Idle/Backfire
Rick makes some good points. It is battery ignition (can be seen in the video).
By the way, your coolant is pushing out because it is over full. Even if it has an overheating problem, it probably wouldn't do it in such little time.
By the way, your coolant is pushing out because it is over full. Even if it has an overheating problem, it probably wouldn't do it in such little time.
- pickerandsinger
- 10+ Years
- Posts: 1501
- Joined: Thu Oct 18, 2012 3:23 pm
- Zip Code: 13143
- Tractors Owned: 1957 Cub Low Boy w/ FH Mott Flail Mower
1953 Cub w/ sprayer and 54A blade (Chompers)
1954 Cub w/fast hitch (Ira)
1948 Cub ( Papa Paul)with Henderson loader..
1951 Mutt mix Cub (BattleAx
1950 Farmall Cub (basket case demo)
Cub parts tractor
2019 " KuB"ota 2601 loader and roto tiller
1951 Ferguson TEA 20 (parts)( Uncle Rusty)
F/H Disc Harrow for cub L-38
C-22 Sickle Bar Mower
IH C2 and C3 mower
Universal tool attachment with disc hillers..Rear cultivators (various tips
York Rake for Cub home made
Single bottom Plow for Cub F194
Gravely 5660 12 hp/ w snoblower.rototiller,bush hog - Circle of Safety: Y
Re: Rough Idle/Backfire
I once screwed up the firing order on my cub....It ran but had very little power...The skip was barely noticeable....I could drive the tractor but couldn't engage the mower...No power...I swear I don't know how I monkeyed up that firing order....But as a last resort I checked it....And I had....Corrected it and ...end of story....
In Memory of 58,286
- Hengy
- 10+ Years
- Posts: 7153
- Joined: Sat Feb 18, 2006 8:12 pm
- Zip Code: 15101
- eBay ID: lacrosseorgans
- Skype Name: Mike.Hengelsberg
- Tractors Owned: 1949 Cub "Merlin"
1955 Cub "Lewis"
Cub Trailer
A-60 Blade
Cub-22 Mower
193 Plow - Circle of Safety: Y
- Location: PA, Allison Park (Am Hengelsberg)
- Contact:
Re: Rough Idle/Backfire
I agree with what others have said, and also will add my questions about the governor linkage. If there is a lot of slop in there, it won't allow the carb butterfly to fully open and you won't get full power. I noticed that when you had the mower deck engaged and also when you were climbing the hill that your rain flapper didn't fully open. That says to me that the engine isn't breathing fully. I just redid the governor slop on Lewis, and now there is almost NO delay in governor response. Merlin's governor has been partially redone, but I need to finish that work because there is still a significant amount of movement in the rod and a delay in "kicking in" of the governor.
Did this happen all of a sudden or has it been down on power for a while?
Mike
Did this happen all of a sudden or has it been down on power for a while?
Mike
Who is online
Users browsing this forum: No registered users and 51 guests