The pictures don't show it all, but most of the process. Some of the things like trimming out the cork and putting in the metal sleeve are not shown. I'll try to suppliment with text as we go.
Most of us have seen the big brother version gas gauge meant for larger Farmall tractors such as this:
My Simplicity lawn tractor has a similar one, but that IH picture inspired me to start doing some thinking (on paper) about how to make one for a Cub:
Materials needed:
1 large cork (outside diameter at large end exceeds 1" diameter)
1 replacement gas gauge
1 plumbing slip joint (1-1/4")
a piece of glass (cut to fit inside the cap of the slip joint)
a piece of sheet metal (weldable, 16 ga +/-)
cork sheet gasket material
two metal bars (stiffeners from a discarded windshield wiper blade)
Get your 1-1/4" slip joint from the home improvement or hardware store. Disassemble and cut the body about 3/4" from the top:
Cut the sheet metal into a disc and fit into the slip joint body. You'll be welding it about half way up into the body (enough head clearance between it and the underside of the glass for your needle to rotate). Now you have your cap, disc, cut slip joint and metal bars:
I drilled my cap and disk/top separately, but on second thought, it might be better to weld the disk/top to the top of your cap first, then drill your hole. I'll show you how I did it and you can do as you please:
Take one of the metal bars from the wiper and drill a small hole (1/16"-5/64"+/-). Just don't drill to the outside edge, it must be a complete hole. Make a mark 1/2" on each side of the hole:
Bend the metal bar as shown at the 1/2" marks and then again at 7-1/2" from the bottom to form feet:
The first gas gauge I made utilized bent metal bar, cutouts for two small screws to attach the metal bar to the cap. But here, I cut a scrap piece of sheet metal and used it to sandwich the feet of the metal bar to the underside of the cap w/ screws (drilled/tapped). It seemed nice and secure when done:
Take the other metal bar and cut the pivot point checking often with the drilled hole for fit:
At this point, I ground off the paint from the cap and welded the top to it using a spacer rod to center the top in place:
Welding brass is not fun. I blew holes through it where not intented. But, I wanted holes for air circulation anyway since the top is covering the two holes in the cap. Need to keep air able to move in/out. Here's the center metal bar cut to length running up through the cap (about 1/2" +/-) taller than the face of the dial:
Cut the glass to fit:
Now, you have the metal frame at 1" distance evenly from top to bottom. Cut two grooves in the sides of the large cork. Drill out a 1/4" +/- hole from the bottom of the cork to the top but don't penetrate the last 1/4". In other words, you'll have a slot cut down through the first 1/4" of the large cork, then it transitions to the 1/4" diameter hole in the bottom. In that slot bend and place a piece of thin sheet metal, tight to the cork (so it won't come out) but with enough clearance to the twisted bar so the cork freely slides up/down along the metal frame.
Twist the rod so when the cork is at the bottom, it's pointing to where you want Empty to be; when the cork is at the top, where you want Full to be. This is largely your preference. I made a dial on the computer and had it copied off at Office Depot or some such store onto oil resistance paper. Here's what we have so far:
Paint the cap:
I cut two cork sheet gaskets to sandwich the glass under the cap ring. Glue in the dial:
Install and enjoy:
DISCLAIMER: The first one I made has been on my '48 for a year. The dial face shows some signs of yellowing, but otherwise seems to be working fine. This whole project was motivated by me NOT using hardener in my paint on the hood. Not wanting to unnecessarily open my gas cap, I chose to make a gauge so I'd know approximately how much has was in the tank. You may find that lengthening or shortening the metal frame suits you better. The 7-1/2" metal frame seems to work well for me.
It was a fun project, but it had times of frustration and challenge. Enjoy.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
How to Make a Cub Gas Gauge
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
- Stanton
- Cub Pro
- Posts: 7760
- Joined: Mon Jun 22, 2009 6:56 am
- Zip Code: 64070
- Tractors Owned: 1942 Farmall AV, serial #87025
1947 Farmall Circle Cub, serial #2116
1948 Farmall Cub, serial #46066 - Circle of Safety: Y
- Location: Lone Jack, MO
-
- 10+ Years
- Posts: 167
- Joined: Sun Nov 25, 2012 12:03 pm
- Zip Code: 16345
Re: How to Make a Cub Gas Gauge
I had that problem on a bike fuel tank I painted. I did a real nice job and then got some gas on it and ruined it. a QT of real 2 part clear coat at the paint store was over 100$ which seemed stupid because I only needed about 2 squirts to clear coat to do a gas tank and then the rest would be waste. Then I discovered spraymaxx 2x. Comes in an aerosol can but there is a button on the bottom you puncture to release the hardener. You then have 8 hours to use it. I bet you could do the whole cub if you were sparing. Definitely do the hood because it is just a matter of time before gas gets on it. I wonder why old non-clear coat paint seems unaffected by gas. Maybe because it has cured for so long or had lead in it or something?
http://www.eastwood.com/spray-max-2k-hi ... MgodXX4Aiw
I like your fuel gauge. i just light a match and look in there
http://www.eastwood.com/spray-max-2k-hi ... MgodXX4Aiw
I like your fuel gauge. i just light a match and look in there
- Rudi
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
Dad's Putt-Putt
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger - Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
- Contact:
Re: How to Make a Cub Gas Gauge
Stanton:
Nicely done and well written . Answered my question on venting as well along with a few others that have been beetlin around in me bonnet since you posted the other thread.
You sure are creative .. thanks for sharing again
Nicely done and well written . Answered my question on venting as well along with a few others that have been beetlin around in me bonnet since you posted the other thread.
You sure are creative .. thanks for sharing again
Confusion breeds Discussion which breeds Knowledge which breeds Confidence which breeds Friendship
- randallc
- Cub Pro
- Posts: 1906
- Joined: Tue Jan 18, 2011 9:16 am
- Zip Code: 72940
- Tractors Owned: 1951 Farmall Cub, 152 disk plow, 2 gang disk, belly mower, sickle mower
1949 Farmall Cub, cultivator, moldboard plow, disk,front blade. Cub Cadet, LTX1045 Mower. Cub Cadet's 109, 125, 1000, and 1250
1961 cub c2 belly mower and full blade. 48 cub manual lift with cultivators.
1947 Cub - Circle of Safety: Y
- Location: Huntington, AR
Re: How to Make a Cub Gas Gauge
Man that is good work.
Going into production yet?
Going into production yet?
- Wakulla Bill
- 10+ Years
- Posts: 358
- Joined: Thu Jun 30, 2011 9:19 pm
- Zip Code: 32327
- Tractors Owned: Now
73 MF 165
63 MF 203 Ind
44 BF Avery "A" Project
51 Farmall Cub
49 Farmall Cub
48 Farmall Super A - Circle of Safety: Y
- Location: Crawfordville, Fla
Re: How to Make a Cub Gas Gauge
Nice and very innovative.
Thanks for sharing this project.
Bill
Thanks for sharing this project.
Bill
"Work smarter; Not harder"
Who is online
Users browsing this forum: No registered users and 49 guests