This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Adjusting the steering Box
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 42
- Joined: Wed May 15, 2013 3:48 pm
- Zip Code: 19938
- Tractors Owned: 69 Cub lowboy
- Contact:
Adjusting the steering Box
Is it just like a car steering box adjust?????????//
- gitractorman
- 10+ Years
- Posts: 2680
- Joined: Mon Oct 24, 2005 11:35 am
- Zip Code: 14072
- eBay ID: toysforjake
- Tractors Owned: Lots of Cub Cadets!
1951 Farmall Cub
1977 IH Cub
1966 IH Cub
1965 IH Lo Boy
1964 IH Lo Boy
1949 Farmall Cub
Several IH 154 Lo Boys
1979 IH 184 Lo Boy
Simplicity 4416 Sovereign
Simplicity Conquest
Simplicity Legacy 4x4 Diesel
Mitsubishi MT180D 4x4 Diesel - Circle of Safety: Y
- Location: Grand Island, NY
Re: Adjusting the steering Box
No. There is one bolt that can be tightened to adjust the amount of effort needed to turn the steering wheel, but this RARELY needs to be adjusted.
More than likely, the combination of the drag link ends and tie rod ends being worn out is your problem. They're all easy to replace. Also, check to see how much play is in the center pivot pin that holds the front axle on. This also wears but shows up as sloppy steering. Then check the front wheel bearings. Again, worn wheel bearings show up as sloppy steering.
More than likely, the combination of the drag link ends and tie rod ends being worn out is your problem. They're all easy to replace. Also, check to see how much play is in the center pivot pin that holds the front axle on. This also wears but shows up as sloppy steering. Then check the front wheel bearings. Again, worn wheel bearings show up as sloppy steering.
Cub Cadets 682, 1811, 1864, Simplicity Legacy XL 4x4 Diesel with FEL, 60" mower, 50" Tiller
-
- 10+ Years
- Posts: 42
- Joined: Wed May 15, 2013 3:48 pm
- Zip Code: 19938
- Tractors Owned: 69 Cub lowboy
- Contact:
Re: Adjusting the steering Box
Thanks What Bolt is adjustable
I do have all the above bad parts , tierods , Pivot pin alittle But the steering Box needs adjusted bad.
after I get back to work I can redo all the bad steereing. The wheel moves 4-5 inches before responce
then the rest of the parts have their play.
I do have all the above bad parts , tierods , Pivot pin alittle But the steering Box needs adjusted bad.
after I get back to work I can redo all the bad steereing. The wheel moves 4-5 inches before responce
then the rest of the parts have their play.
-
- Team Cub Mentor
- Posts: 20377
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Adjusting the steering Box
The adjusting screw fastened to the cover plate tends to wear a bit. Turning the adjusting screw in 90 degrees (1/4 turn) may take some of the slack out of the steering.
The steering sector appears to be quite similar to the Ross used on Cub Cadets. A kit is available for replacing the ball bearings and races. Common problem with the Ross steering sector is that the plastic retainers for the ball bearings break after years of use. Next common problem is wear on adjusting screw.
The bearing kit is relatively inexpensive. A new adjusting screw, more expensive.
Any way, if the slop is centered in the steering sector, a complete rebuild is normally necessary. The rebuild is not difficult. The difficulty is removing the sector from the tractor.
The steering sector appears to be quite similar to the Ross used on Cub Cadets. A kit is available for replacing the ball bearings and races. Common problem with the Ross steering sector is that the plastic retainers for the ball bearings break after years of use. Next common problem is wear on adjusting screw.
The bearing kit is relatively inexpensive. A new adjusting screw, more expensive.
Any way, if the slop is centered in the steering sector, a complete rebuild is normally necessary. The rebuild is not difficult. The difficulty is removing the sector from the tractor.
I have an excuse. CRS.
- RaymondDurban
- Cub Pro
- Posts: 4435
- Joined: Wed Dec 26, 2007 7:45 pm
- Zip Code: 32536
- Circle of Safety: Y
- Location: FL, Crestview
Re: Adjusting the steering Box
If you pull on the steering wheel up and down (in/out) and it has movement, then the upper and lower bearings are bad, or the end cap needs tightening up.
If you turn the wheel and it takes several degrees of wheel movement before the pitman moves, then the screw adjustment on the side of the gearbox needs to be turned in to force the arm closer to the worm shaft. Turn it in just enough to take out the play without causing binding.
If you turn the wheel and it takes several degrees of wheel movement before the pitman moves, then the screw adjustment on the side of the gearbox needs to be turned in to force the arm closer to the worm shaft. Turn it in just enough to take out the play without causing binding.
Screwstick #3934
FCub - LoBoy - Numbered Series - Power Unit Databases
FCub - LoBoy - Numbered Series - Power Unit Databases
-
- 10+ Years
- Posts: 7388
- Joined: Sat Jul 22, 2006 5:02 pm
- Zip Code: 00000
- Location: in northern usa
Re: Adjusting the steering Box
When your done adjusting it remember to grease it.
I'm technically misunderstood at times i guess its been this way my whole life so why should it change now.
Return to “Lo-Boy Series - 154, 184, 185”
Who is online
Users browsing this forum: No registered users and 16 guests