This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Splitting The Cub
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 489
- Joined: Thu May 19, 2005 2:04 pm
- Zip Code: 35216
- Tractors Owned: 1947 Cub
1949 Cub
2011 JD X320 - Circle of Safety: Y
- Location: Birmingham Al/Bay Springs Ms.
Splitting The Cub
I am to the point now of splitting my tractor in order to replace my broken 1st/reverse gear - battery case, floorboard and seat removed for easier access. I looked through the CBoK and was unable to locate any discussion about how to properly support the sections when splitting. I am positive that I have seen one or more illustrations of how other folks have made supports, but I sure didn't find them. Could someone direct me to where this has been previously discussed? (By the way, I thought that I had posted this question yesterday, but cannot even find my posting. I must be losing my mind!!) Thanks
Since retirement, the things I miss most are the holidays!
- Mike in Louisiana
- 10+ Years
- Posts: 7831
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: Splitting The Cub
Check out the how to forum. This is just one type. I like the ones that use a trailer jack bolted to a 1/2 in plate.
Back end, overhead hoist, engine hoist or blockek up real good. DON'T FORGET WEDGES FOR FRONT AXLE.
Back end, overhead hoist, engine hoist or blockek up real good. DON'T FORGET WEDGES FOR FRONT AXLE.
Last edited by Mike in Louisiana on Fri Feb 22, 2013 9:25 am, edited 2 times in total.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
-
- 10+ Years
- Posts: 804
- Joined: Tue Apr 17, 2012 7:55 pm
- Zip Code: 47119
- Skype Name: ntrenn
- Tractors Owned: 63 Cub 221833 in family since '69
65 Lo-boy 19648 with an un-stuck #4 - it lives!!!
144 Cultivators with disc hillers
193 Plow
42C mower
59L mower mounted on the Fcub
23A Disc - lost possession - Circle of Safety: Y
- Location: Indiana
Re: Splitting The Cub
I bolted an 1x6 oak leg to each side of the tube. Didn't have a spare boat jack around.
- Bill Hudson
- Team Cub
- Posts: 9526
- Joined: Wed Jul 26, 2006 10:50 am
- Zip Code: 44057
- Tractors Owned: 57 F-Cub - Dad & Mom's Cub
77 F-Cub - Red Long Stripe - Circle of Safety: Y
- Location: OH, Madison
Re: Splitting The Cub
Check the How To forum under Specialty Tools. LOTS of splitting stands of various levels of sophistication. Hope this helps.
-
- 10+ Years
- Posts: 489
- Joined: Thu May 19, 2005 2:04 pm
- Zip Code: 35216
- Tractors Owned: 1947 Cub
1949 Cub
2011 JD X320 - Circle of Safety: Y
- Location: Birmingham Al/Bay Springs Ms.
Re: Splitting The Cub
Well, here is another case of missing post. Just after Mike replied to my query, I created a response and sure thought that I had clicked the "submit" button, but I don't see it anywhere.
Nevertheless, my post was to thank Mike for his reply and pointing me to the "how to " forum. That is where I had previously seen the info. Thanks also for your reply, ntrenn & Bill.
I was pleased to meet you, Mike and especially pleased to try out your famous pineapple upside-down cake at the DSCF. Stanley
Nevertheless, my post was to thank Mike for his reply and pointing me to the "how to " forum. That is where I had previously seen the info. Thanks also for your reply, ntrenn & Bill.
I was pleased to meet you, Mike and especially pleased to try out your famous pineapple upside-down cake at the DSCF. Stanley
Since retirement, the things I miss most are the holidays!
-
- 10+ Years
- Posts: 62
- Joined: Sun Dec 09, 2012 11:22 am
- Zip Code: 36303
- Tractors Owned: !
'52 Cub - Circle of Safety: Y
Re: Splitting The Cub
Another variation on the theme:
For the rear half, I used a jackstand beneath the tranny and another beneath the drawbar. It balances fairly well on the rear tires. As already mentioned, don't forget to block the front axle. Two or three long bolts will help with alignment and support during disassembly and reassembly.
Also, pay close attention to the front seal retainer on the tranny - if installed backwards, the main shaft crawls forward and the PTO doesn't work. Here's a pic:
For the rear half, I used a jackstand beneath the tranny and another beneath the drawbar. It balances fairly well on the rear tires. As already mentioned, don't forget to block the front axle. Two or three long bolts will help with alignment and support during disassembly and reassembly.
Also, pay close attention to the front seal retainer on the tranny - if installed backwards, the main shaft crawls forward and the PTO doesn't work. Here's a pic:
- Mike in Louisiana
- 10+ Years
- Posts: 7831
- Joined: Tue Feb 15, 2005 10:10 am
- Zip Code: 71023
- Circle of Safety: Y
- Location: LA, Doyline
Re: Splitting The Cub
thiggy wrote:I was pleased to meet you, Mike and especially pleased to try out your famous pineapple upside-down cake at the DSCF. Stanley
Stanley it was a pleasure meeting you also. Glad you liked the cake.
To bad you did not have the gear on hand, it would have been split and back together in no time.
1975 cub (LouAnn) serial # 245946, 1941 John Deere Model H
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
Good judgment comes from experience,
and a lot of that comes from bad judgment. Will Rogers
- Bill V in Md
- 10+ Years
- Posts: 1124
- Joined: Sun Feb 02, 2003 6:51 pm
- Zip Code: 21228
- Tractors Owned: 1948 Farmall Cub
LT1045 Cub Cadet - Circle of Safety: Y
- Location: MD, Catonsville
- Contact:
Re: Splitting The Cub
After the tractor is split at the rear, don't depress the clutch pedal. This could cause the clutch disc to slip off center once the input shaft is removed.
Bill VanHooser
Cub 54 Blade, Cub 193 Moldboard Plow, Cub 28A Disc Harrow
Cub 54 Blade, Cub 193 Moldboard Plow, Cub 28A Disc Harrow
-
- 10+ Years
- Posts: 489
- Joined: Thu May 19, 2005 2:04 pm
- Zip Code: 35216
- Tractors Owned: 1947 Cub
1949 Cub
2011 JD X320 - Circle of Safety: Y
- Location: Birmingham Al/Bay Springs Ms.
Re: Splitting The Cub
Bill V, thanks for your clutch warning. Thinking about it, it is obvious, but I might not have thought about it till too late. Your reminder will help me keep that in mind.
Since retirement, the things I miss most are the holidays!
-
- 10+ Years
- Posts: 489
- Joined: Thu May 19, 2005 2:04 pm
- Zip Code: 35216
- Tractors Owned: 1947 Cub
1949 Cub
2011 JD X320 - Circle of Safety: Y
- Location: Birmingham Al/Bay Springs Ms.
Re: Splitting The Cub
John, I especially like your supports because I am not a welder and this looks quite sturdy. Do you know what the size of the rectangular tubing is used there?
Since retirement, the things I miss most are the holidays!
-
- 10+ Years
- Posts: 62
- Joined: Sun Dec 09, 2012 11:22 am
- Zip Code: 36303
- Tractors Owned: !
'52 Cub - Circle of Safety: Y
Re: Splitting The Cub
thiggy wrote:John, I especially like your supports because I am not a welder and this looks quite sturdy. Do you know what the size of the rectangular tubing is used there?
I think that was 2" x 4" x 1/4" tubing I had cut for a boom pole that my pallet forks could slip into. Ended up using wider tubing for the boom pole. A bit long and definitely overkill, but it was there and unused...
-
- Team Cub Mentor
- Posts: 20378
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Splitting The Cub
Any number of methods of supporting a tractor when splitting it.
I use a shop crane/cherry picker over the front of a Cub with a wide heavy duty strap around the engine. Rear end, supports similar to ones previously shown or a large floor jack.
I also have a couple of homemade jack stands with U shaped bracket on top. U shaped bracket holds a 4" x 4". The jack stands with 4 x 4 fits under the torque tube.
A reminder, be sure to wedge the bolster to front axle.
I use a shop crane/cherry picker over the front of a Cub with a wide heavy duty strap around the engine. Rear end, supports similar to ones previously shown or a large floor jack.
I also have a couple of homemade jack stands with U shaped bracket on top. U shaped bracket holds a 4" x 4". The jack stands with 4 x 4 fits under the torque tube.
A reminder, be sure to wedge the bolster to front axle.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 175
- Joined: Tue Sep 07, 2010 9:09 pm
- Zip Code: 98271
- Tractors Owned: 1947 cub
1947 Gibson E - Location: Marysville, WA
Re: Splitting The Cub
Simplest, cheapest method is to place solid 2x8s from front axle to rear hitch, then place solid 2x4 cross pieces at tube and oil pan. Add blocking as needed. Put a little grease where the 2x4s and 2x8s meet so the 2x4s slide easily when you split the tractor. Fine tune the height of each half with shims between the 2x4s and 2x8s as needed when you put the cub back together. The 2x8's also make handy places to keep tools, parts, and nourishment as you work on the cub.
If you don't have a rear hitch, you could suspend the 2x8s from the rear axles, or support them with cement blocks. Nail a cross-piece that butts against the rear tires for stability if you use cement block support.
If you don't have a rear hitch, you could suspend the 2x8s from the rear axles, or support them with cement blocks. Nail a cross-piece that butts against the rear tires for stability if you use cement block support.
Who is online
Users browsing this forum: Majestic-12 [Bot] and 33 guests