Farmall C & Super C Tractors, 1948-1954
Moderator: Team Cub
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Your Super C is a 1952. They all had the C-123 engine. Standing on the right side of the tractor, you should find a machined spot on the block on the forward, upper part of the right side of the block. The engine serial number should be stamped there.
MD, Deep Creek Lake
"1950 Something" Farmall Cub
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Good to know.
Right now I'm trying to get a list of things I will need come spring when I can get it inside to pull the head.
So far I know I'll need a can of kroil.
But I'm also thinking of getting plastigage, some push rods, and a head gasket set, and maybe a oil pan gasket.
In the mean time I'll just keep pushing the snow off of it and spraying mystery oil in it.
Valve spring compressor and a torque wrench to plastigage the crankshaft journals. Probably borrow them from the auto parts store. NAPA use to have loaner tools. Perhaps other auto parts stores. You will need other specialized tools as you get deeper into the engine.
Parts. Do not order any parts until you have determined what you need - have measured the engine parts and assessed needed machine work and parts.
Example: You will need a valve cover gasket, head gasket, and pan gasket just to remove the head and pan. It may be cheaper to purchase a complete gasket set for the tractor than buying the 3 gaskets separately.
I have an excuse. CRS.
Yup, don't buy any engine parts unless/until you have it apart. Even then you'd probably ought to wait for the advice of the machinist before buying anything.
No telling how many times its been rebuilt or what's in there. You could have standard, .002, .010, or larger oversize bearings in the mains and rods. Standard or overbore pistons/sleeves.
I think the overbore pistons give you 132 cubic inches vs. the standard 123.
Well I decided to bring the tractor inside. Its a little tight but I think it will work.
This weekend I was able to pull the cylinder head off and drop the oil pan.
Looking at the crankshaft things don't look to bad, its fairly clean.
With the head off I'm able to get a closer look at the cylinder walls and two of them have some slight surface rust on them.
I'm kinda lost on what to do next, thinking of getting plastigage and checking the crankshaft bearings.
I'll post pics soon.
Refresh my memory, is the engine stuck?
With the head off you could try the "fire" method. Basically you fill each cylinder with diesel fuel and light them on fire, one at a time. Clearly this should be done OUTSIDE, away from buildings.
Not sure about building a fire in each cylinder. Any way, engine stuck or not, put enough solvent in each cylinder to cover entire edges of the piston head. Some solvent will either evaporate or drain into the crankcase - just refresh the solvent level every day. Tractor in high gear, rear wheel, rock the tractor back and forth - checking for stuck engine.
Reach inside each cylinder. Finger nail against cylinder wall drag upward - you are looking for the ring ridge. If significant, enough to catch the finger nail, you will need a ridge remover. Ridge must be removed before pulling the pistons.
I would push out each piston after plastigaging the crankshaft journal.
I have an excuse. CRS.
The engine is Not stuck. All the pistons are moving.
Good to know about the ring ridge Eugene, The book I have mentions it and I know there is a special tool used. I will do the finger nail method and see what I find.
I got some plastigage today and have a few questions. In the plastigage kit it came with the "green" 0.001 to 0.003 inch and the "red" 0.002 to 0.006 inch.
I'm wondering what one I should use because in the service manual under the specifications section for the crankshaft its a little confusing.
There are three main bearings on the crankshaft. What I'm confused with is the differeance between the main bearing running clearance which is 0.0009 to 0.0039
and the Maximum permissible main bearing clearance which is 0.0055.
Which one do I go by and what size plasitgage do I use?
Use the .002 - .006, or the red stick.
Running clearance is the measurement between the dry (no oil) bearing insert and the dry crankshaft journal on a newly rebuilt engine. Maximum permissible clearance is = time for an overhaul. Kinda a rule of thumb is that you want .001" of clearance for each inch of crankshaft journal diameter.
Not sure where the .0009" clearance came from. I&T, IH-8 lists the Series C main bearing running clearance as .001 - .0035. Since the C's main journals (standard) are listed at 2.124 - 2.125" I would like to see around .002" clearance with new inserts.
I have an excuse. CRS.
That definitely helps.
I was thinking;
When I go to torque the bolts on the main bearings (to 78 foot-pounds) I think I’m going to have to use an extension on my torque wrench.
Will the extension on the wrench affect my accuracy? I’m using the clicker type torque wrench.
In theory, a socket extension will have an effect as the extension itself will have some torsional twist. It is well within the margin of error in your wrench, however. There are tables out there that can be used if you are curious, but it would probably be more beneficial to calibrate the wrench than worry about the extension! Edit: thinking about this, the torque is transmitted right through the entire system and as long as everything is straight you are OK. Something like a crow's foot would change things as you are changing your fulcrum.
If you are talking about a cheater bar on the end of the wrench to get more leverage- that is meaningless.
Good to know about the torque wrench, thank you.
I used the "red" plastigage last night on the center main bearing. I wiped everything clean before I used it and after torqueing the bolts to the 78 ft lbs I got
I have not done the other two bearings yet. Question I have is should the bolts be dry? I didn't clean the oil off of the bolts before re-torqueing them.
Also will the temp in the garage affect my results? It has been pretty cold here in NH, I bet it was around 10 degrees F in the garage last night.
My plan is to do the other two bearings tonight. I'm also going to use a different torque wrench tonight to see how it compares to the one I have been
This will tell you all you need to know about torquing bolts under different conditions: http://www.farmallcub.com/fcman/download.php?fname=./files/Reference%20Info/Torque%20*%20Bolt%20ID.pdf
.005" is at the upper end of permitted clearance. Temperature will make a very minor difference in the clearance reading. Not enough difference to change the .005" indicated clearance. Remove the bearing insert from the rod and main caps and record the numbers with cap and insert location. Numbers will indicate the journal size.
I have an excuse. CRS.
Who is online
Users browsing this forum: No registered users and 2 guests