ammeter

Farmall Cub Forum -- Questions and answers to all of your Cub related issues.

Moderator: Team Cub

Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
HART
10+ Years
10+ Years
Cub Star
Cub Star
Posts: 136
Joined: Wed Jun 02, 2004 2:19 pm
Location: NORTH INDIANA

ammeter

Postby HART » Mon Nov 19, 2012 3:40 pm

' 52 CUB running good in this fine clean up weather. However.... still trying to figure out why ammeter shows in" CHARGE " area when the lights are turned " ON. " Also, when starting, the starter sometimes hesitates before cranking starts. A few times it "grunts", then it either turns over, or maybe not. Battery and coil are new. Thought's ??

lazyuniondriver
Cub Star!!
Cub Star!!
Posts: 438
Joined: Tue Aug 07, 2012 1:37 am
Zip Code: 44134
Tractors Owned: 1949 & 1951 Farmall Cubs

Several Snapper Garden Tractors
Circle of Safety: Y
Location: Southern Suburbs of Cleveland, Ohio

Re: ammeter

Postby lazyuniondriver » Mon Nov 19, 2012 4:55 pm

The starter itself or its connections back to the battery need serviced. Try servicing all the connections first.

Does the ammeter move to charge when the lights are turned on with the engine stopped or running?
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
Image

Eugene
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 15050
Joined: Fri Jul 02, 2004 9:52 pm
Zip Code: 65051
Circle of Safety: Y
Location: Mo. Linn

Re: ammeter

Postby Eugene » Mon Nov 19, 2012 5:00 pm

6 volt electrical system. Battery positive ground?
I have an excuse. CRS.

User avatar
oronc
10+ Years
10+ Years
501 Club
501 Club
Posts: 643
Joined: Thu Jan 19, 2006 11:37 am
Zip Code: 24153
Tractors Owned: 1950 Allis Chalmers B, 1942 Farmall H,Kubota B2150hst
48 Cubplow,cultiv,carry all,blade.other stuff
and other junk
Location: SALEM VA.

Re: ammeter

Postby oronc » Tue Nov 20, 2012 10:14 am

Take the band off the starter and see if the brushes are shot if not broke in half. Also could be cable time as well.

HART
10+ Years
10+ Years
Cub Star
Cub Star
Posts: 136
Joined: Wed Jun 02, 2004 2:19 pm
Location: NORTH INDIANA

Re: ammeter

Postby HART » Tue Nov 20, 2012 3:23 pm

yes, 6 volt, positive ground, and ammeter shows charge when lights are turned on and engine stopped or running. my son - in law put a new coil on. what happens if wires could be on backwards. I will CHECK OUT THE STARTER as suggested. thank you.

User avatar
Denny Clayton
10+ Years
10+ Years
501 Club
501 Club
Posts: 4122
Joined: Wed Feb 05, 2003 1:18 pm
Zip Code: 45365
Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
Circle of Safety: Y
Location: OH, Sidney

Re: ammeter

Postby Denny Clayton » Tue Nov 20, 2012 3:54 pm

dhart wrote:yes, 6 volt, positive ground, and ammeter shows charge when lights are turned on and engine stopped or running. my son - in law put a new coil on. what happens if wires could be on backwards. I will CHECK OUT THE STARTER as suggested. thank you.

What happens when the wires are reversed is the ammeter will show a charge when the lights are on.
'61 Lo-Boy
'60 FH Lo-Boy
'60 Lo-Boy
'57 FH Cub "Rusty"
'48 Cub
C-3 mower, FH Woods 42F, 54A blade, L-54 blade, 194 plow, FH L-38 disk, FH LB disk, 144 cultivators, FH platform carrier

Eugene
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 15050
Joined: Fri Jul 02, 2004 9:52 pm
Zip Code: 65051
Circle of Safety: Y
Location: Mo. Linn

Re: ammeter

Postby Eugene » Tue Nov 20, 2012 4:53 pm

Denny Clayton wrote:
dhart wrote:yes, 6 volt, positive ground, and ammeter shows charge when lights are turned on and engine stopped or running. my son - in law put a new coil on. what happens if wires could be on backwards. I will CHECK OUT THE STARTER as suggested. thank you.
What happens when the wires are reversed is the ammeter will show a charge when the lights are on.
I read that as the wires at the ignition coil could be reversed. Reversing the wires on the coil will not have a different effect in the electrical generating circuit or direction the amp meter needle moves.

Was the amp meter changed out or the wires on the amp meter removed and then reinstalled?

Multimeter at battery. Check to see that the generator is charging correctly as per the battery polarity. Battery positive terminal grounded. If so exchange wires on the back of the amp gauge.

The other thing you could do is to negative ground the battery and then repolarize the regulator.
I have an excuse. CRS.

lazyuniondriver
Cub Star!!
Cub Star!!
Posts: 438
Joined: Tue Aug 07, 2012 1:37 am
Zip Code: 44134
Tractors Owned: 1949 & 1951 Farmall Cubs

Several Snapper Garden Tractors
Circle of Safety: Y
Location: Southern Suburbs of Cleveland, Ohio

Re: ammeter

Postby lazyuniondriver » Tue Nov 20, 2012 5:34 pm

Does the ammeter needle move at all or does it stay in one position?
"HAVE ALL YOUR DELIVERIES MADE BY UNION DRIVERS"
Image

HART
10+ Years
10+ Years
Cub Star
Cub Star
Posts: 136
Joined: Wed Jun 02, 2004 2:19 pm
Location: NORTH INDIANA

Re: ammeter

Postby HART » Wed Nov 21, 2012 3:22 pm

ammeter needle does move around. sometimes to charge. sometimes slight discharge. battery is new so should'nt show too much change. maybe it is just cleaning up the connection's on everything. I do wonder though why needle jumps way over to charge when lights are turned on.

User avatar
Bus Driver
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 2900
Joined: Sat Feb 11, 2006 5:26 pm
Location: NC

Re: ammeter

Postby Bus Driver » Wed Nov 21, 2012 4:13 pm

If the power supply to the light switch is on the battery connection at the starter, that would make the generator (with engine running) increase the amperage in order to power the lights without draining the battery. And the ammeter would show that. But if the engine was stopped, that hookup would not move the ammeter at all if the lights were turned on- because the current is not flowing through the ammeter. Normally, turning on the lights with the engine running causes the ammeter to show a lesser charge rate (with the 6 volt systems) because the generator has limited output amperes and the lights are using most of that before it gets to the ammeter.
With the proper (original schematic) electrical system, turning on the lights with the engine stopped shows a significant discharge rate on the ammeter.
I suspect that someone prior to your ownership did some creative (that is not a compliment) alterations to the electrical system.

The original Cub wiring was such that the ammeter shows net amperes going to and from the battery, not necessarily what the generator was producing at the moment.
Luck favors those who are prepared

User avatar
Bus Driver
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 2900
Joined: Sat Feb 11, 2006 5:26 pm
Location: NC

Re: ammeter

Postby Bus Driver » Thu Nov 29, 2012 7:45 am

The owner of this tractor has not posted back regarding findings/progress, if any. Thinking about this again, the power supply connection for the lights, and perhaps the ignition, could have been switched to the battery post on the starter OR to the post on the ammeter that connects to the battery post to recharge the battery. Might be as simple as just moving a wire terminal from one post on the ammeter to the other. Evidently his tractor does not have a voltage regulator with a lighting terminal in use.
Since he reports no electrical problems at this time other than the ammeter readings, the system apparently works for properly recharging the battery. And could continue to do so for a long time into the future. But the operator is not getting the best information from the ammeter about the present performance of the system.
An analog voltmeter at the battery can test for proper voltage output of the generator (and regulator, if there is one).
Luck favors those who are prepared

User avatar
John *.?-!.* cub owner
Team Cub Guide
Team Cub Guide
501 Club
501 Club
Posts: 21530
Joined: Sun Feb 02, 2003 2:09 pm
Zip Code: 63664
Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
Location: Mo, Potosi

Re: ammeter

Postby John *.?-!.* cub owner » Thu Nov 29, 2012 10:20 am

Been kind of busy lately, and missed the beginning of this thread. If the ammeter shows charge when you speed the engine up, but drops back to the center or close to it when you turn the lights on, that is pretty much normal. The lights draw approximately 2.8 amps each, so if all are on bright, you are drawing 8.4 amps. Standard on a cub generator if they are in top shape is only 11 amps on the earlier ones, less if the brushes are worn or out of adjustment, etc. So you should not expect to see more than a 2 amp or so charge when running at full throttle with the lights on, and that is not much needle movement.
If you are not part of the solution,
you are part of the problem!!!

HART
10+ Years
10+ Years
Cub Star
Cub Star
Posts: 136
Joined: Wed Jun 02, 2004 2:19 pm
Location: NORTH INDIANA

Re: ammeter

Postby HART » Thu Nov 29, 2012 1:33 pm

Thank you BUSDRIVER and ALL others. Gave up and gave '52 cub with ammeter questions to local mechanic. If solution is noteworthy, will post his findings.

User avatar
Bus Driver
Team Cub Mentor
Team Cub Mentor
501 Club
501 Club
Posts: 2900
Joined: Sat Feb 11, 2006 5:26 pm
Location: NC

Re: ammeter

Postby Bus Driver » Fri Nov 30, 2012 10:40 am

I hope it all works out well. Many of the mechanics today were born long after alternators became the norm, witnessed by the fact that this Cub owner started out posting about his alternator.
Unless the mechanic is familiar with the generator/cutout/regulator systems, he will either just give up, just start swapping parts, or spend time educating himself. The tuition bill can be steep.
Luck favors those who are prepared


Return to “Farmall Cub”

Who is online

Users browsing this forum: No registered users and 4 guests