Farmall Cub Forum
Moderator: Team Cub
12 posts • Page 1 of 1
While working on my Cub today getting ready for winterization. I have heard an exhaust noise for sometime, sounded like the clamp for the underslung exhaust was not sealing correct. Well after doing some carb work today i started the Cub while sitting on my stool next to it.
I have been fooling with these tractors off and on for over 40 years and never noticed until today the small hole in the exhaust manifold that points forward to direct warm air onto the breather pipe. The reason is clear.
Its not a crack or anything like that its an obvious factory hole. Were all Cubs from 47 onward built with the hole?????????
Pretty sure they all have it, it is actually a drain hole for any water or condensate that finds it's way into the manifold.
'52 Cub ("Great Personality") 148xxx
'48 Cub with FH ("Gunny Cub") 38xxx
'57 Lambretta (a slow work in progress)
'74 Triumph TR6 (Mama's toy)
As Rick said it is there to drain the condensate out of the exhaust system. Any one who has started the Cub on a cool, damp morning knows that this tractor fogs and spits quite a bit before she warms up. If you shut her down before she is warmed up, that condensate is better outside than sitting inside the exhaust manifold. The crankcase is also prone to build up condensate, especially with short operating times. It is evident by the milky gunk that forms on the dip stick inside the breather tube.
A lot of them are plugged by rust, but I have never seen a manifold without the hole.
"The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the
government lest it come to dominate our lives and interests." Patrick Henry
Agreed. I've seen a lot of them that looked like there was no hole, but if you dig around it'll show up.
'60 FH Lo-Boy
'57 FH Cub "Rusty"
'56 FH Cub
(2) '48 Cubs
'75 IH 140 w/1000 loader
C-3 mower, FH Woods 42F, 22 sickle (2), 54A blade, L-54 blade, 194 plow, FH L-38 disk, FH LB disk, 144 cultivators, FH platform carrier
This subject seems to be answered but with no pictures; so here's an old thread with pictures.http://www.farmallcub.com/phpBB2/viewtopic.php?f=1&t=56308
O.K. But they made it so it is pointing a little forward, just enough to hit the metal tube part of the air breather.
Wonder if that was done on purpose to drain water off the manifold but also to warm the front of the carb in cold weather to help stop venture effect. Thoughts????????????????????
I doubt it would heat any air enough to make any difference going into the carb.
I don't believe in taking the bull by the horns. I took a goat by the horns once and that was enough excitement for me.
Barnyard Bash CubFest May 31 - June 1, 2013
Click here for info.
Anyone who has been around a Cub knows the amount of air the fan pushes back past the engine...the air coming from that hole is blown away before it goes anywhere.
"More gold has been mined from the thoughts of men than has been taken from the earth." -- Napoleon Hill
I suppose I just have not spent enough time around them to know everything, that is kind of why I asked the question. However I do find it odd that on my 140 and 240 the holes are in the manifold so that also drain in the area onto the carb throat.
I went back in my memory banks, and one time years ago I had a Farmall H and was using during a blizzard to move snow.
She quit while I was moving from one location to another. I called my friend who has since passed away, he worked for years at the local IH dealership in town back when we had weather that was colder than now 1950-1965. He fooled with it some and told me she was iced up, he was looking at the frost on the intake manifold near the carb throat.
He said"if I remember correct" that it was a problem that they cured by adapting the heat shield off of a distilate manifold to keep heat onto the areas prone to icing.
12 posts • Page 1 of 1
Who is online