Hengy wrote:gcbailey wrote:Hengy wrote: I have another one I can try, probably will try....
Did you do a repair on the dash that is on it? How about the tabs on the hood? Were these repaired or replaced?
No.... I still have the original dash on it, but it looks like there is somewhat more of a forward lean to it than there should be, but I don't know how much front lean/tilt/slant it should have either. It is a long ear dash. The tabs on the hood have not been touched, when the hood is on it appears to mate pretty good, but again, I don't have a "correct" one to go by to know how tight of a mate it should be.
If it is just sitting on the dash and is not hooked up, then it isn't the dash that is making the problem. Are the bolts attached to the radiator supports through the tabs on the inside of the hood? Try taking those off and keeping the bolts loose on the doglegs until the grille is mounted. Then cinch down the dogleg bolts (all eight) and the dash mounts. Then remove the grille and hopefully the hood doesn't move. Then try putting the bolts in the radiator supports. You may have to move the supports around...
I'm going to do another post with pics of the dash and my "progress" using a soft rubber mallet and some beveled finish washers.....
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
what am I doing wrong?
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 204
- Joined: Fri Aug 26, 2011 5:59 am
- Zip Code: 24740
- Tractors Owned: '49 Farmall CUB #62395
'62 Cub Cadet
'69 Cub Cadet 73 w/Haban Sickle bar
'71 Cub Cadet 127
'76 Cub Cadet Sof76
'07 Cub Cadet LT1045
'09 Cub Cadet GT2544 - Circle of Safety: Y
- Location: Princeton, WV
Re: what am I doing wrong?
-
- 10+ Years
- Posts: 204
- Joined: Fri Aug 26, 2011 5:59 am
- Zip Code: 24740
- Tractors Owned: '49 Farmall CUB #62395
'62 Cub Cadet
'69 Cub Cadet 73 w/Haban Sickle bar
'71 Cub Cadet 127
'76 Cub Cadet Sof76
'07 Cub Cadet LT1045
'09 Cub Cadet GT2544 - Circle of Safety: Y
- Location: Princeton, WV
Re: what am I doing wrong?
Here's what I've got accomplished so far.... nothing really due to the fact that I have had to "rig" it up... I did take a rubber mallet and tap along the front bottom and top... Now it almost seems like where the hood meets the doglegs is holding it out and keeping it from going back in. It's that "so close...." feeling.
-
- 10+ Years
- Posts: 908
- Joined: Sat Feb 15, 2003 7:20 am
- Zip Code: 00000
Re: what am I doing wrong?
It seems the screen grilles for me are always an issue after I’ve taken them off. Maybe I get to rough when I sand blast/wire brush them. I never used an aftermarket grille so I don’t know the short comings of them.
It looks like you need to stretch the grille to fit it around sheet metal. It’s like Chris D stated: You may have to get a little rough. Arizona Mikes’ post is the one that works best for me even on the original grilles. The first one I had troubles with years ago I consulted George Willer about and he told me to cut wood fixtures out of plywood to reshape the grille before installation. He also said "to put the hood on the tractor and shape the grille before painting than remove again for painting". I tried to find the measurements George sent me for making the fixtures but I misplaced them but I still have the pictures that came with the specs.
First thing is mask off all paint interference areas to protect it as best as you can. Use the low adhesion masking tape if you painted with Alkaloid enamel .Next make a 1”x 4” wood firing strip about 3 to 5’ long with a shoulder mount cushion at the end of the firing strip for more force if needed. Put the 1x4 in the pocket of your shoulder (where you put the butt of a shotgun) with an assistant do like Dale Shaw stated but using the wood firing strip pushing firmly against the grille brackets until they are in place.
Hope this helps. Sorry cell phone picture...
George Willers’ fixtures: Sorry I can’t find the measurements he sent me.
It looks like you need to stretch the grille to fit it around sheet metal. It’s like Chris D stated: You may have to get a little rough. Arizona Mikes’ post is the one that works best for me even on the original grilles. The first one I had troubles with years ago I consulted George Willer about and he told me to cut wood fixtures out of plywood to reshape the grille before installation. He also said "to put the hood on the tractor and shape the grille before painting than remove again for painting". I tried to find the measurements George sent me for making the fixtures but I misplaced them but I still have the pictures that came with the specs.
First thing is mask off all paint interference areas to protect it as best as you can. Use the low adhesion masking tape if you painted with Alkaloid enamel .Next make a 1”x 4” wood firing strip about 3 to 5’ long with a shoulder mount cushion at the end of the firing strip for more force if needed. Put the 1x4 in the pocket of your shoulder (where you put the butt of a shotgun) with an assistant do like Dale Shaw stated but using the wood firing strip pushing firmly against the grille brackets until they are in place.
Hope this helps. Sorry cell phone picture...
George Willers’ fixtures: Sorry I can’t find the measurements he sent me.
Last edited by Jack fowler on Wed Oct 17, 2012 8:55 am, edited 1 time in total.
-
- 10+ Years
- Posts: 204
- Joined: Fri Aug 26, 2011 5:59 am
- Zip Code: 24740
- Tractors Owned: '49 Farmall CUB #62395
'62 Cub Cadet
'69 Cub Cadet 73 w/Haban Sickle bar
'71 Cub Cadet 127
'76 Cub Cadet Sof76
'07 Cub Cadet LT1045
'09 Cub Cadet GT2544 - Circle of Safety: Y
- Location: Princeton, WV
Re: what am I doing wrong?
I have thought about tapping on those side tabs and I can see them flying across the garage now! I will try that out. I did a few of the things from Arizona Mike's post and that how I managed to at least get it on there.
-
- 10+ Years
- Posts: 908
- Joined: Sat Feb 15, 2003 7:20 am
- Zip Code: 00000
Re: what am I doing wrong?
I would only push not hit... maybe with your hand a little.
-
- Team Cub
- Posts: 17313
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: what am I doing wrong?
You don't have a picture that shows it well, but it appears to me that the lower edges of the hood are bulging out. With the grill removed you should be able to check for a straight line between the points the upper and lower corners of the grill should be when installed. If the hood bulges out, you need to readjust it so the edges of the hood and dogleg form one continuous straight line.
-
- 10+ Years
- Posts: 2731
- Joined: Sun Oct 03, 2004 7:11 am
- Zip Code: 03848
- eBay ID: panelbeata
- Tractors Owned: 1947 circle cub
1950 cub demonstrator
1957 cub
1967 cub - Circle of Safety: Y
- Location: NH, Kingston
Re: what am I doing wrong?
what i would try is take the doglegs of and bolt them to the grill then using drifts pins pull them back into position using the mounting holes as the pull points. i've used this method with aftermarket body parts with good results. its worth a try.
-
- 10+ Years
- Posts: 204
- Joined: Fri Aug 26, 2011 5:59 am
- Zip Code: 24740
- Tractors Owned: '49 Farmall CUB #62395
'62 Cub Cadet
'69 Cub Cadet 73 w/Haban Sickle bar
'71 Cub Cadet 127
'76 Cub Cadet Sof76
'07 Cub Cadet LT1045
'09 Cub Cadet GT2544 - Circle of Safety: Y
- Location: Princeton, WV
Re: what am I doing wrong?
Jim Becker wrote:You don't have a picture that shows it well, but it appears to me that the lower edges of the hood are bulging out. With the grill removed you should be able to check for a straight line between the points the upper and lower corners of the grill should be when installed. If the hood bulges out, you need to readjust it so the edges of the hood and dogleg form one continuous straight line.
The hood bulges out on the sides where the doglegs attach.... with the doglegs screwed to the bolster I do have to press in on each side of the hood and doglegs to even get the grille to start. Again, it sucks not knowing how things should be or have another one to physically reference by.
So.. I take it the hood should not bulge outward in the area where the headlights/dogleg connection is?
-
- Team Cub
- Posts: 17313
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: what am I doing wrong?
gcbailey wrote:So.. I take it the hood should not bulge outward in the area where the headlights/dogleg connection is?
Right.
-
- 10+ Years
- Posts: 5236
- Joined: Tue Jan 12, 2010 2:08 pm
- Zip Code: 12514
- Circle of Safety: Y
Re: what am I doing wrong?
The rear hood support "dash panel" is slotted so it has some slop in it also, try loosening the rear bolts and sliding the whole unit forward so you have more room between the bolster and grille, the brackets on the front of the hood are slotted also so make sure to loosen them also
Tim
Tim
-
- 10+ Years
- Posts: 4565
- Joined: Wed Feb 05, 2003 1:18 pm
- Zip Code: 45365
- Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
- Circle of Safety: Y
- Location: OH, Sidney
Re: what am I doing wrong?
gcbailey wrote:The hood bulges out on the sides where the doglegs attach.... with the doglegs screwed to the bolster I do have to press in on each side of the hood and doglegs to even get the grille to start. Again, it sucks not knowing how things should be or have another one to physically reference by.
So.. I take it the hood should not bulge outward in the area where the headlights/dogleg connection is?
Years ago, when I tore my one and only Cub apart, I bought another one to have for reference. Somehow they've multiplied to seven (not counting the ones I sold).
-
- Team Cub
- Posts: 24282
- Joined: Tue Aug 07, 2007 3:39 pm
- Zip Code: 45030
- Tractors Owned: At This Time
40 Farmall Cubs (Round Hood)
2 Farmall Cub (Square Hood)
2 IH Cubs (Square Hood)
5 Lo-Boys (Round Hood)
2 Lo-Boys (Square Hood)
2 Farmall 404's
1 Farmall H
1 Ferguson 20
1 Cub Cadet 125
1 Kubota B-7100 - Circle of Safety: Y
- Location: OH, New Haven (Hamilton County)
Re: what am I doing wrong?
Denny Clayton wrote:Somehow they've multiplied to seven
That can happen if you're not careful.
There are two ways to get enough Cubs. One is to continue to accumulate more and more. The other is to desire less.
-
- 10+ Years
- Posts: 4565
- Joined: Wed Feb 05, 2003 1:18 pm
- Zip Code: 45365
- Tractors Owned: Home to "Rusty", the 2007 and 2009 Cub Tug Champion.
- Circle of Safety: Y
- Location: OH, Sidney
Re: what am I doing wrong?
Barnyard wrote:Denny Clayton wrote:Somehow they've multiplied to seven
That can happen if you're not careful.
Bill, your water supply is more fertile than mine.
-
- 10+ Years
- Posts: 4955
- Joined: Tue Jun 08, 2004 3:04 pm
- Zip Code: 14559
- Circle of Safety: Y
- Location: Rochester, NY
Re: what am I doing wrong?
It looks like you're not tight against the hood on top, OR against the bolster on the bottom. There's enough of a gap there to get the grille mostly in place, anyway.
All it will take is a little massaging. Figure out where the grille is hitting, and re-form those areas so it doesn't hit.
All it will take is a little massaging. Figure out where the grille is hitting, and re-form those areas so it doesn't hit.
-
- 10+ Years
- Posts: 204
- Joined: Fri Aug 26, 2011 5:59 am
- Zip Code: 24740
- Tractors Owned: '49 Farmall CUB #62395
'62 Cub Cadet
'69 Cub Cadet 73 w/Haban Sickle bar
'71 Cub Cadet 127
'76 Cub Cadet Sof76
'07 Cub Cadet LT1045
'09 Cub Cadet GT2544 - Circle of Safety: Y
- Location: Princeton, WV
Re: what am I doing wrong?
Matt Kirsch wrote:It looks like you're not tight against the hood on top, OR against the bolster on the bottom. There's enough of a gap there to get the grille mostly in place, anyway.
All it will take is a little massaging. Figure out where the grille is hitting, and re-form those areas so it doesn't hit.
right now as mentioned before, I *think* where the hood wants to bulge out where the doglegs attach is keeping it from sliding on back in. I just need to know the best way to *caress* the hood to keep the sides from popping out.
I would have no problem with having a few more cubs to reference by! That's how it started with my Cadets.... I know where a good looking 140 is, my problem is I need something that I can justify keeping at the house and not at the grandparents an hour away!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 16
- 608
-
by Joeandmack
Wed Nov 02, 2022 11:52 am
-
-
Is this bent or welded wrong? Attachment(s)
by smallfarm » Sat Jan 14, 2023 8:18 pm » in Farmall Cub - 2
- 277
-
by smallfarm
Sat Jan 14, 2023 9:26 pm
-
-
-
Paint, because I did it wrong last time.
by AndrewSpencer » Wed Apr 17, 2024 4:19 pm » in Farmall Cub - 10
- 412
-
by Pothole31a
Sat Apr 27, 2024 3:05 pm
-
-
-
Spring in Wrong place in Cub Hydraulics Attachment(s)
by bookman51 » Sun Sep 03, 2023 4:35 pm » in Farmall Cub - 8
- 587
-
by Glen
Tue Sep 05, 2023 4:55 pm
-
Who is online
Users browsing this forum: EIREfarmer and 3 guests