What is the proper way to set the high idle? I put an electronic ignition on my 1977 184 and tried to set the high idle to 2400 rpm by putting more tension on the governor with the throttle control arm. This works but, the governor spring then seems to pull hard enough to overcome the friction of the throttle adjust cable and it just slows the fast idle down.
I tried the method in the book and backing off the maximum throttle speed adjusting screw on the governor but, if the throttle adjust lever is already at it's furthest travel you get no more rpms. Best I could get there was 2200 or maybe 2250. I can get the higher rpms by cherating the throttle cable but, like I said it backs off then. W@hat else can I do? Thanks
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
High idle setting
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 176
- Joined: Mon Jul 02, 2007 5:17 am
- Zip Code: 16656
- Tractors Owned: 1977 Cub 184 Lowboy
1979 John Deere 2640
2013 Kubota L3800 TLB
1949 International Cub - Location: West Central PA
-
- 10+ Years
- Posts: 134
- Joined: Tue Aug 03, 2010 11:34 am
- Zip Code: 46975
Re: High idle setting
I pretty much had the same problem. I ended up tightening the throttle lever pivot bolt. IIRC, use a 7/16 open end through the RH side of the throttle lever slot, and a 1/4" drive with a 7/16 socket from the outside of the LH side of the pedestal. Feel up under there and you'll feel/see a hole that lets you get the socket on. Try it little by little, it doesn't take much.
-
- 10+ Years
- Posts: 2795
- Joined: Tue Jul 22, 2008 12:44 pm
- Zip Code: 48370
- Tractors Owned: 184
- Location: Oxford, MI
Re: High idle setting
Make sure you are measuring engine RPM's and not PTO RPM's. They aren't the same. The PTO turns slower than the engine.
184 w/ Creeper & 3-Point
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
IH 3160a Mower
IH Model 15 Tiller
IH-54 Blade
-
- 10+ Years
- Posts: 176
- Joined: Mon Jul 02, 2007 5:17 am
- Zip Code: 16656
- Tractors Owned: 1977 Cub 184 Lowboy
1979 John Deere 2640
2013 Kubota L3800 TLB
1949 International Cub - Location: West Central PA
Re: High idle setting
Thanks guys.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 335
-
by outdoors4evr
Mon Dec 06, 2021 5:46 am
-
-
High crop number series lowboy Attachment(s)
by SamsFarm » Wed Jan 12, 2022 8:34 pm » in Lo-Boy Series - 154, 184, 185 - 8
- 609
-
by SONNY
Sat Jan 15, 2022 5:34 pm
-
Return to “Lo-Boy Series - 154, 184, 185”
Who is online
Users browsing this forum: No registered users and 0 guests