This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
cc 102 steering sloppy
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 245
- Joined: Mon Aug 22, 2005 5:24 pm
- Zip Code: 44847
- Location: sandusky, Oh on lake erie
cc 102 steering sloppy
I am working on a cub cadet 102 narrow frame tracotr. There is a bunch of play in the steering wheel shaft at the top of the steering wheel. How should I go about removing this shaft to replace or repair this bearing? I quite honestly havent looked into it too much yet but was about to order some engine parts soon and figured I better figure out if I will need a new bearing also before I place the order. I will also be needing decals for this tractor as it is scheduled to get painted as well. Does anyone recommend where to get the decals from? Jake
-
- 10+ Years
- Posts: 3736
- Joined: Sun Jul 13, 2008 10:05 pm
- Zip Code: 45067
- Tractors Owned: 1951 Cub, 2-1955 Loboy w FH, a few plows, discs, mowers, blades, carrier & such
Several '61 CC Originals, Cub Cadet 100, several 102's & 122's, 124, various CC options & implements, #1Trailer, 1963 Springfield, JD 770, Ford 8N - Circle of Safety: Y
- Location: OH, Trenton
Re: cc 102 steering sloppy
Jake,
If you are referring to the part under the steering wheel, at the top of the tube, you will need to remove the steering wheel. From what I have read and learned, removing the steering wheel can be one of the biggest challenges with working on these Cadets. Start soaking the steering wheel nut with your favorite penetrating solution (Kroil), give it some time to do its thing. Once you get the nut loose go get another one from a hardware store, should be a little thicker, and also get a 3” bolt, same thread. Thread the new bolt about halfway on the steering shaft and the new bolt in the other half. Sit in the seat, lift the wheel with your knees, and give the bolt a whack with a big hammer. Hopefully the shaft will move on the wheel, keep tapping (while lifting on the wheel with your knees) until the wheel touches the new nut. You should be able to remove the nut and work the wheel off then. Some people recommend removing the cap on the other end of the shaft (bottom) and backing out the cam bolt out before this doing process. The bearing is under the wheel and it just pops out, it is plastic. Some people recommend replacing it with a wheel bearing the same size, but I had no luck with that, it didn’t seat in the tube and came out, so I went back to the original one, it should last me another 40 years!
Call Ken at C&G (site sponsor); he can hook you up on needed parts.
I recently picked up a 102 with a replacement 12 hp in it, I got it running and no smoke, and it runs great! I have started piddling with it, fixing the little things and I think I will put quick paint job on it.
Good luck,
If you are referring to the part under the steering wheel, at the top of the tube, you will need to remove the steering wheel. From what I have read and learned, removing the steering wheel can be one of the biggest challenges with working on these Cadets. Start soaking the steering wheel nut with your favorite penetrating solution (Kroil), give it some time to do its thing. Once you get the nut loose go get another one from a hardware store, should be a little thicker, and also get a 3” bolt, same thread. Thread the new bolt about halfway on the steering shaft and the new bolt in the other half. Sit in the seat, lift the wheel with your knees, and give the bolt a whack with a big hammer. Hopefully the shaft will move on the wheel, keep tapping (while lifting on the wheel with your knees) until the wheel touches the new nut. You should be able to remove the nut and work the wheel off then. Some people recommend removing the cap on the other end of the shaft (bottom) and backing out the cam bolt out before this doing process. The bearing is under the wheel and it just pops out, it is plastic. Some people recommend replacing it with a wheel bearing the same size, but I had no luck with that, it didn’t seat in the tube and came out, so I went back to the original one, it should last me another 40 years!
Call Ken at C&G (site sponsor); he can hook you up on needed parts.
I recently picked up a 102 with a replacement 12 hp in it, I got it running and no smoke, and it runs great! I have started piddling with it, fixing the little things and I think I will put quick paint job on it.
Good luck,
David
-
- 10+ Years
- Posts: 245
- Joined: Mon Aug 22, 2005 5:24 pm
- Zip Code: 44847
- Location: sandusky, Oh on lake erie
Re: cc 102 steering sloppy
thanks, I'll look into it this week and see what I cane do. I like the idea of removing whatever is on the bottom of shaft. I would hate so pound on the shaft and not have the wheel give as something is gonna have to take the energy of the blow...
-
- Team Cub Mentor
- Posts: 20394
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: cc 102 steering sloppy
I use my Cub's belt pulley puller to remove the steering wheel from my Cub Cadets.
Under the steering wheel is a plastic bushing that fits in the steering column and between the shaft.
Might want to remove the entire steering column and at least disassemble and clean up. If required, a kit is available to replace the ball bearings, races, felt and gasket.
There are several adjustments to/in the steering sector. A new kit and adjustments will take a lot of the slop out of the steering.
Under the steering wheel is a plastic bushing that fits in the steering column and between the shaft.
Might want to remove the entire steering column and at least disassemble and clean up. If required, a kit is available to replace the ball bearings, races, felt and gasket.
There are several adjustments to/in the steering sector. A new kit and adjustments will take a lot of the slop out of the steering.
I have an excuse. CRS.
-
- 10+ Years
- Posts: 7388
- Joined: Sat Jul 22, 2006 5:02 pm
- Zip Code: 00000
- Location: in northern usa
Re: cc 102 steering sloppy
Try to tighten up the nut at the bottom of the steering box on the steering lever first. This should take out some of the play first. Do not over tighten it. Remember to grease it too at the sametime.
I'm technically misunderstood at times i guess its been this way my whole life so why should it change now.
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3
- 4632
-
by seahaul
Wed Oct 25, 2023 3:54 pm
Who is online
Users browsing this forum: No registered users and 0 guests