This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Hobart welder-Wisconsin engine
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Hobart welder-Wisconsin engine
I bought a 1971 Hobart welder, G-213, with a Wisconsin TJD 2 cyl engine. The "runs good, welds good" was not exactly true but I got it running and welding but still needs some carb work. It has 2 speeds, 1800 for welding and 2200 rpm for use as a generator. The throttle knob is a T shaped handle connected to a small chain that goes to the govenor linkage. There is no lock of any form that I can see. I am not sure how to lock it at either of the two speeds. The parts diagram does not show that area clear enough for me to tell if I am missing a throttle lock. Anyone familiar with these welders than can tell me what I may be missing?
-
- Team Cub
- Posts: 17278
- Joined: Sun Feb 02, 2003 2:59 pm
- Zip Code: 55319
- Circle of Safety: Y
- Location: MN
Re: Hobart welder-Wisconsin engine
Did you try pulling then turning the handle?
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Re: Hobart welder-Wisconsin engine
I turned the handle thinking it would lock but it did not. I took apart the handle looking for any notches or locks and there are none. This may not be the original throttle control and I may have to file some notches into the hadle shaft.
- Virginia Mike
- 10+ Years
- Posts: 1300
- Joined: Tue Nov 23, 2004 7:21 pm
- Zip Code: 24095
- Tractors Owned: '49 Cub
'49 JD "B"
'79 JD 2040
'50 DB "Garden Tractor"
'52 DB "Super Power"
'56 DB "Big 5"
'62 DB "Super 600"
'37 McCormick Deering "LA" engine - Location: Stewartsville, Virginia
Re: Hobart welder-Wisconsin engine
Is the hole the handle comes through key-hole shaped, so the handle can be pulled out and locked in the notch?
Best,
Mike
Tractors are made to work!
"A Cub will do as much as a team of horses,.. More in hot weather!" - C. W. Spradlin 1909-1994
Mike
Tractors are made to work!
"A Cub will do as much as a team of horses,.. More in hot weather!" - C. W. Spradlin 1909-1994
-
- Team Cub Mentor
- Posts: 20377
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: Hobart welder-Wisconsin engine
TJD Wisconsin manual shows two speed controls: 1) TT-66 variable speed governor control assembly and 2) TT-66-F Idle control assembly.
TT-66F: Shows a knob which is lifted, moving a rod out of a slot on the back of the tappet cover. Engine speed set, then the knob lower - moving the rod into the slot.
TT66: Is the one with the small chain. It appears to function like the old manual choke controls. Pull/push only. I'm looking at the parts photo. There appears to be a nut on the back side that may control the tension on the shaft.
Starting procedure - simply states to set the throttle position in 1/2 open position. Doesn't explain further.
TT-66F: Shows a knob which is lifted, moving a rod out of a slot on the back of the tappet cover. Engine speed set, then the knob lower - moving the rod into the slot.
TT66: Is the one with the small chain. It appears to function like the old manual choke controls. Pull/push only. I'm looking at the parts photo. There appears to be a nut on the back side that may control the tension on the shaft.
Starting procedure - simply states to set the throttle position in 1/2 open position. Doesn't explain further.
I have an excuse. CRS.
- John *.?-!.* cub owner
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: Hobart welder-Wisconsin engine
Are you sure 2200 rpm is for the generator? That would be a very unusual speed. Normally they are 1800 or 3600.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- Team Cub Mentor
- Posts: 5640
- Joined: Thu Aug 03, 2006 6:20 am
- Zip Code: 43358
- Tractors Owned: 48 Cub Diesel (Cubota)
53 Cockshutt 20 restored (Shooter)
52 Cockshutt 20 unrestored
47 Leader "B" (Herckie)
49 Leader "D" (Princess)
49 Leader "D" very rough
48 Leader "D" unrestored
Kubota B6200E
Kubota B6200HST
Kubota B8200HST-D - Circle of Safety: Y
- Location: OH West Mansfield
Re: Hobart welder-Wisconsin engine
We had one of those welders where I used to work. Pull the throttle and twist the t-handle to the right to lock. I don't think there were any notches or such, just a friction lock, which may be adjustable. It could be locked in any desired throttle position.
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
Re: Hobart welder-Wisconsin engine
Thanks for the replies. I expect the lock is just missing. Likely I will just drill a few holes in the throttle knob shaft and place a pin to set the correct distance.
The generator does run at 1800 rpm and 2200 for the welder. I had it backwards.
The generator does run at 1800 rpm and 2200 for the welder. I had it backwards.
Return to “Other Tractors and Machinery”
Who is online
Users browsing this forum: No registered users and 15 guests