Perry Mini CubFest ~ Dartmouth MA

My father's address is:

470 Bakerville Road
Dartmouth, MA 02748

There is plenty of room for a few cubs and lots of projects inside of the shop and there is spillover room inside of the adjacent barn.

So far, there are two touch control units to rebuild, a clutch to repair, and a broken bolt to remove from a radiator housing.
 
Greg has two projects but I don't what they are. I do want to try and swap out the short shaft and maybe put the engine in. whoa boy, it is a carcass right now not much on ole' Rusty.
 
ScottyD'sdad":3d3g4es1 said:
spaceghost":3d3g4es1 said:
I will be there, I will try to break something before I come so that I have something to work on.

Bob Phillips
Click to expand...

Bob, haven't you rebroken the flail mower, yet? Ed
Click to expand...

Well it still cuts grass but I am missing a row of blades now so it leaves stripes on the lawn. I cut for two day in Maine and hit a lot of rocks and other things.
It needs a tune up.
 
spaceghost":3ofpxslh said:
ScottyD'sdad":3ofpxslh said:
spaceghost":3ofpxslh said:
I will be there, I will try to break something before I come so that I have something to work on.

Bob Phillips
Click to expand...

Bob, haven't you rebroken the flail mower, yet? Ed
Click to expand...

Well it still cuts grass but I am missing a row of blades now so it leaves stripes on the lawn. I cut for two day in Maine and hit a lot of rocks and other things.
It needs a tune up.
Click to expand...

I expected it to be more broke than that, by now! Ed
 
Chuckwheat Farm":aci5uyi0 said:
Bob...do you need any blades? Ted's in Fairhaven has them in stock I believe.
Click to expand...

Chris
I have a bag of them so I don't think I need anymore at this point.

Thanks anyway.
 
How did they go missing??? In hours and hours of pretty rough mowing I am missing one pair of knives.

I will probably bring along the stray 'front end' I have. Need to get the shroud, 'bent' radiator and steering gear apart. The bolster is going on the 64 that's been repaired. I will drag along a couple of carbs too... one needs to be flattened and the other just needs the kit installed.
 
Chuckwheat Farm":19fmoueu said:
Buzzard Wing":19fmoueu said:
How did they go missing??? In hours and hours of pretty rough mowing I am missing one pair of knives.
Click to expand...
Larry he runs over porcupines on purpose. :D
Click to expand...

I have shot 5 porcupines this year but 0 got mowed over. I might bring the mower with me. I had some realy high weeds and I could not see the bolders.
I worked the mower hard for two days.
 
spaceghost":2fipt95p said:
Chuckwheat Farm":2fipt95p said:
Buzzard Wing":2fipt95p said:
How did they go missing??? In hours and hours of pretty rough mowing I am missing one pair of knives.
Click to expand...
Larry he runs over porcupines on purpose. :D
Click to expand...

I have shot 5 porcupines this year but 0 got mowed over. I might bring the mower with me. I had some realy high weeds and I could not see the bolders.
I worked the mower hard for two days.
Click to expand...

Oh I thought you ran out of ammo. :?
 
Cecil":26pyky9w said:
I guess that means I had better bring my carb box.
Click to expand...

Looks like a few carb rebuilds, Wally and Larry being rebuilding carbs. I'm considering doing one but might have too much on my plate. Cecil could you pick me up a kit at Columbia Tractor? Are they still $75 or so?

Wally will be bringing the cloth wiring harness he made, with enough extra wiring and connectors to show the folks how to make another harness.

Two TC units rebuilds are still onboard. Looks like Bob's shop should have alot of activity.
 
Chris I have a spare TM kit for $46 if you would rather have that. A lot more stuff and cheaper. Only difference is the needle valve.
 
Cecil":3ni738cg said:
Chris I have a spare TM kit for $46 if you would rather have that. A lot more stuff and cheaper. Only difference is the needle valve.
Click to expand...
Sounds good, thank you! You bringing a tractor down?
 
Less than a week to go for the minifest. :D

I am finishing a woodworking project so that the workshop will be all clear for cub projects. Also today I will be splitting my cub so that we're ready to work on the clutch.

BobinCT copied the latest cub manual file for me at Cecil's and if anyone would like a copy please bring a 2 gb thumb drive on Saturday.

~ Jim
 
Chris I am bringing Ugly Cub down to Ed's to cut some wood with the Brookfield. If you guys would like I could probably bring it with me. Got any wood to cut?
Chris I will bring the kit with me.
 
I have another person coming, with a cub, who needs points and condenser installed in his mag. Cecil has been volunteered to assist him. Name is Ross MacVicar, from Plymouth, Ma. Met him at a small show we did, at a Lions club festival, on Sunday. Another SouthEastern Massachusetts cubber! Ed
 
You must log in or register to reply here.
Back
Top