Having the hood off of Ellie "oh No !!! " , actually has been a bit of a energizer for me to get a bunch of projects that needed doing done. Another one of the projects that I had been putting off (cause I had never attempted it before) was routing the battery cable properly which necessitated a new one After trying to run the existing cable where it needed to be, I found out I was about 6 inches short or around 80 inches +/- in length. So while I was out looking for other stuff... Em suggested since Ellie is our primary snow removal machine that I actually spend the extra dollars to buy the proper length cable and not patch the existing one.
Oh ok.. says I with a twinkle in me eye... How often does the better half say go spend money on a Cub -- so I promptly went in to Traction, our local NAPA for Heavy Equipment and bought 8 feet of 2 ought cable, a couple good copper starter ends, a pair of cable junctions, a couple of good heavy duty solder on battery terminal ends and some decent 3:1 shrink tube.
This is my attempt at building a decent battery cable. Be forwarned, the routing of my cable is not exactly correct. For the correct method of routing the battery cable please refer to Big Dogs rather good Cub Battery Cables How To article in the CBoK. I am electrically/electronically challenged, but I can plumb which means I can sweat a good joint which is similar to soldering electrical components pretty much methinks. Couple thing to remember about electrical work with solder and flux. Ensure that you do not use acid core solder or acid core flux when working on electrical cables. Acid core may corrode connections and this is the last thing we want or need. Use silver solder as that is the better product to use on electrical wiring.
First I cut and trimmed the 2/0 cable end, dunked it in flux and soldered it to the copper starter terminal.
I then slid on about 3" of 3:1 shrink tube for 2/0 cable which is about 3/4" OD and 5/8" ID.
Apply heat carefully over the length and circumference of the shrink tube in numerous passes with the propane torch. Used the propane torch as I do not own a heat gun. (gonna be a future purchase though ) A little patience and voila, first joint is done.
Next step is to start feeding the cable where it needs to go. After making sure that the cable will clear the starter lever, I gave myself a bit of slack cause one never knows what will come later, and ran the new cable along the best route I have with my setup.
I utilized the Oil Pressure Gauge line as the spine and routed to the dash corner and then down under the clutch pedal stop. The rear light cable joins the harness at this point and will follow the battery cable to it's obvious conclusion.
Since I no longer have cable clips under the deck, I purchases some Grote 80-7008 1/2" Cable Clips. Should have actually gotten the 3/4". Sure would have been a lot easier to install when you have that litte extra room the larger clip will give you. But it still worked out nicely and the Battery Cable and Rear Light Cable are safely tucked up underneath the deck now.
Once the cable has been routed under the deck and back up through the gap between the axle housing/operator deck and the Battery Box, I measured what I needed to get to the negative terminal on the Group 1 Battery and added about 3 more inches to be safe.
Ithen slid on the next 3" piece of 3:1 shrink tube. The next step is to trim, dunk in flux, insert the 2/0 into the heavy duty battery cable terminal end.
Apply some heat from the propane torch and solder the connection together. Let it cool for about 5 minutes.
Slide the 3:1 shrink tube over the terminal butt (be careful, it will still be hot. Use pliers etc., to hold the end if need be).
Apply heat carefully over the length and circumference of the shrink tube in numerous passes with the propane torch.
A nice moisture proof connection now that will not corrode at the joint. Still have to clean the ends occassionaly.
Connect the cable end to the Battery and you are pretty well done aside from putting on the front and the top.
I have added a ring terminal to the end of the small red cable that connects my amber flashing light. Fits nicely onto the bolt and provides a good solid connection. Only thing Ihave left to do is to put some di-electric grease on the terminals to prevent corrosion.
While I was at this project, Granny needed a little TLC in the Battery Cable department too. So I utilized the leftover 2/0 cable I bought, along with the other package of 3:1 shrink tube and a cable splicer. I cleaned and trimmed all the ends of the existing cable, soldered on a copper starter terminal end and then made the joint between the two pieces. Done the same way - both ends trimmed, 3 pieces of shrink tube slid on the appropriate pieces, dunked the ends in flux, inserted both ends into the junction and then soldered the joint. I then repeated the same process for the other heavy duty battery terminal end. Once cooled a bit, I then repeated the previous steps for the shrink tube process. Now Granny also has a Battery Cable that will route correctly from starter to battery. A rather enjoyable little project.
2 each : Grote 82-9436 2/O Copper Tube Lugs 1/2"
2 each : Straight Barrel Clamp
3 each: Flexible Dual Wall, 3:1 - Adhesive Lined, Black, Heat Shrink Tubing
3 each: 84-7009 3/4" Black 1/2" Vinyl Insulated Steel Clamps
Additonal Material For Granny's Spliced Cable:
1 each : 82-9556 2/O Tin Plated Butt/Splice Connectors
Batteries, magnetos, distributors, wiring harnesses and more.
Moderator: Team Cub
1 post • Page 1 of 1
- Cub Pro
- Posts: 28706
- Joined: Sun Feb 02, 2003 8:37 pm
- Zip Code: E1A7J3
- Skype Name: R.H. "Rudi" Saueracker, SSM
- Tractors Owned: 1947 Cub "Granny"
1948 Cub "Ellie-Mae"
1968 Cub Lo-Boy
IH 129 CC
McCormick 100 Manure Spreader
McCormick 100-H Manure Spreader
Post Hole Digger
M-H #1 Potato Digger
- Circle of Safety: Y
- Twitter ID: Rudi Saueracker, SSM
- Location: NB Dieppe, Canada
Last edited by Barnyard on Fri Mar 09, 2018 11:44 am, edited 2 times in total.
Reason: fix broken link
Reason: fix broken link
- Similar Topics
- Last post
by Coventry plumber
Mon Sep 04, 2017 6:09 pm
Thu Aug 31, 2017 9:20 pm
Tue Mar 13, 2018 1:58 pm
Thu Aug 04, 2016 5:13 pm
Sun Oct 30, 2016 6:32 pm
Who is online
Users browsing this forum: No registered users and 0 guests