- Soak in penetrating oil (Liquid wrench, Marvel Mystery Oil, diesel fuel, WD40, oil of wintergreen, bore cleaner). Allow time to work. I like to soak the rusted fastiner once weekly for a month or two with diesel fuel.
- Gently hammer the proper sized bolt out from Sears, Irwin, Home Depot and twist counter clockwise.
- If broken off then stud remover (if stub is long enough) or spiral extractor, or multispined extractor after drilling proper sized hole.
- Heating with torch then applying penetrating oil when warm not red hot.
- Burning the nut off with torch.
- Using torch to weld another nut.
- Striking the bolt or nut with hammer and with medium force then more penetrating oil.
- Cutting groove in nut with dremel and then enlarging groove with chisel and then more penetrating oil.
- Cutting off nut with cut off wheel.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
How to Remove a Rusty Nut or Bolt
-
- 10+ Years
- Posts: 286
- Joined: Thu Nov 04, 2004 11:50 pm
- eBay ID: falco-de-fiume
- Location: NE, Cheney
How to Remove a Rusty Nut or Bolt
I know this is elementary to most, but a few may need the knowledge and most might learn one more technique. Here are a few suggestions:
Si hoc legere scis,nimium eruditionis habes.
-
- 10+ Years
- Posts: 1055
- Joined: Thu Feb 06, 2003 9:21 am
- Zip Code: 93510
- Location: Acton Ca.
To remove larger bolts 3/8 and up that are deep seated the following works:
- Drill the bolt out with the largest bit you can use that won't damage the bolt hole threads
- Use a saber saw with a narrow metal cutting blade and saw through what is left of the bolt in three or four places. Don't worry if you saw into the threads a little it won't hurt anything.
- Take some bread, not Mama's homemade, but the doughy stuff and put it in the drilled hole. With a small chisel or screw driver loosen one of the bolt pieces and extract with a small set of needle nose pliers. The bread will keep the bolt pieces from falling into the hole and will desolve in water or oil.
- Put a sealer on the new bolt and you're ready to go.
I just removed two hydraulic fittings I busted off. Sounds like it would leak if you saw into the threads but I have never had one do so. Maybe one of our plumbers can tell us why it doesn't.
- Drill the bolt out with the largest bit you can use that won't damage the bolt hole threads
- Use a saber saw with a narrow metal cutting blade and saw through what is left of the bolt in three or four places. Don't worry if you saw into the threads a little it won't hurt anything.
- Take some bread, not Mama's homemade, but the doughy stuff and put it in the drilled hole. With a small chisel or screw driver loosen one of the bolt pieces and extract with a small set of needle nose pliers. The bread will keep the bolt pieces from falling into the hole and will desolve in water or oil.
- Put a sealer on the new bolt and you're ready to go.
I just removed two hydraulic fittings I busted off. Sounds like it would leak if you saw into the threads but I have never had one do so. Maybe one of our plumbers can tell us why it doesn't.
Always try the easiest thing first.
-
- 10+ Years
- Posts: 145
- Joined: Mon Jan 02, 2006 2:52 am
- Location: SW PA... US
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Restoring Old Rusty
by Gdoucette » Tue Sep 21, 2021 9:13 pm » in Farmall M, Super M, 400, 450, & 560 - 0
- 975
-
by Gdoucette
Tue Sep 21, 2021 9:13 pm
-
-
-
Best way to remove paint
by ShawnAgne » Sun Aug 01, 2021 5:47 am » in Farmall A, Super A, AV, 100, 130 & 140 - 11
- 791
-
by ShawnAgne
Sat May 28, 2022 8:41 pm
-
-
- 6
- 492
-
by Greg49G
Mon Dec 13, 2021 6:17 pm
-
- 2
- 197
-
by tst
Thu May 26, 2022 9:51 pm
-
-
How would you Remove this Continental Belton Mower? Attachment(s)
by buddylindsey » Sat Apr 27, 2024 9:56 pm » in Farmall Cub - 5
- 220
-
by tmays
Mon Apr 29, 2024 8:19 pm
-
Who is online
Users browsing this forum: No registered users and 2 guests