This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
H
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 1631
- Joined: Fri Dec 22, 2006 6:28 am
- Zip Code: 37743
- Circle of Safety: Y
- Location: Tennessee East
H
Can the wheels in an H be reversed ? I need about 4" to get it on a trailer.
47 Cub (Glenda)
52 Super A
62 Cub (Genie)
43 H
42 M
In all things know which way the wind is blowing.
52 Super A
62 Cub (Genie)
43 H
42 M
In all things know which way the wind is blowing.
-
- 10+ Years
- Posts: 4113
- Joined: Thu Nov 09, 2006 11:26 pm
- Zip Code: 61722
Re: H
yes the can! just turn the dish in instead of out and slide back on the axles! thanks; sonny
-
- 10+ Years
- Posts: 5880
- Joined: Thu Jul 28, 2005 2:37 pm
- Zip Code: 44645
- eBay ID: kevinb2366
- Tractors Owned: 47 Cub 48 Cub 50 H
- Location: Marshallville Ohio
Re: H
Boy that sounds like a lotta fun!!! NOT!!! Kevin
47 CUB[Krusty] 49 CUB[Ollie] 50 H-- PLOWS DISCS MOWERS AND lots more stuff!!Life is to short -Have fun now cause ya ain't gonna be here long!!!!
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: H
Not too big a job, depending on whether you have fluid or weights. A cherry picker makes it much easier. If the wheels haven't been moved in a while, the clamp bolts may be hard to loosen. 2 inside and 2 outside, per wheel. One word of warning, once the wheels are reversed, the tread is pretty narrow and will make it easy to tip over.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
- Posts: 1631
- Joined: Fri Dec 22, 2006 6:28 am
- Zip Code: 37743
- Circle of Safety: Y
- Location: Tennessee East
Re: H
Good news! Now I just have to figger out how to get it on the trailer with those front tires. My trailer has ramps.
47 Cub (Glenda)
52 Super A
62 Cub (Genie)
43 H
42 M
In all things know which way the wind is blowing.
52 Super A
62 Cub (Genie)
43 H
42 M
In all things know which way the wind is blowing.
-
- Cub Pro
- Posts: 23701
- Joined: Sun Feb 02, 2003 2:09 pm
- Zip Code: 63664
- Tractors Owned: 47, 48, 49 cub plus Wagner loader & other attachments. 41 Farmall H.
- Location: Mo, Potosi
Re: H
Assuming it is a trailer with 2 ramps, either borrow a third one, or else drive up to the trailer at a 90 degree angle (rear wheels next to end of ramps). When the rear wheel lines up with the ramp, cut the steering wheel all the way while riding the brake. The front wheels will go up the other ramp, and be right at the edge just as they hit the trailer. Keep on swinging around till you are straight, and then just drive on. One word of caution doing this, if you do not cut the wheels and ride the brakes hard enough at the same time, it may tend to push the ramps off the side of the trailer. As a safety precaution, I have welded a couple pieces of angle at the end of the ramp brackets to keep them from sliding off the end of angle brackets. Of course, this only works loading nose first, not backing on.
If you are not part of the solution,
you are part of the problem!!!
you are part of the problem!!!
-
- 10+ Years
Re: H
I have removed H wheel/tire assemblies by first totally removing the clamp to give plenty of slop. Then lower tractor to within a bout 2" of the ground. Use a 2 wheel dolley to remove using that extra space where the clamp was removed. If just adjusting loosen clamp with slot down and insert a greased wire. Roll wheel 180 and slide on wire then roll back to remove wire. They actually sold a flat bar for this that had ball bearings crimped into it about 1/2" apart.
Return to “Farmall H, HV, Super H, 300 & 350”
Who is online
Users browsing this forum: No registered users and 1 guest