Hi All,
Does anyone know what size bolt will fit the hole on the end of the crankshaft? (front)
It looks to be a 9/16 or 5/8.
Thanks,
Ron
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Bolt size
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- Team Cub Mentor
- Posts: 24144
- Joined: Sun Feb 02, 2003 12:50 pm
- Zip Code: 43113
- Circle of Safety: Y
- Location: OH, Circleville
I believe that's a 1/2" - NC
Bigdog
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
If you can't fix it with a hammer, you've got an electrical problem.
My wife says I don't listen to her. - - - - - - - - Or something like that!
http://www.cubtug.com
-
- 10+ Years
- Posts: 994
- Joined: Mon Feb 03, 2003 11:10 am
- Zip Code: 40023
- Tractors Owned: 1948 FCub
1957 LoBoy - Circle of Safety: Y
- Location: KY, Fisherville
-
- 10+ Years
- Posts: 80
- Joined: Sat Feb 08, 2003 11:23 am
- Location: Columbus, Georgia
Bolt size
Thanks to all who responded!!
After I finally got the fan pulley off, I discovered that the threads in my crank
have been gone for some time.
It appears that they were pulled out.
I was able to tap the deeper, smaller hole to a 7/16 x 14 so I would at least have something.
I believe I would have to go up to at least a 5/8 size to re-thread the outer part of the crank.
Thanks again!!
Ron
After I finally got the fan pulley off, I discovered that the threads in my crank
have been gone for some time.
It appears that they were pulled out.
I was able to tap the deeper, smaller hole to a 7/16 x 14 so I would at least have something.
I believe I would have to go up to at least a 5/8 size to re-thread the outer part of the crank.
Thanks again!!
Ron
1951 Farmall Cub
-
- Similar Topics
- Replies
- Views
- Last post
-
- 2
- 265
-
by Leewebb7
Thu Dec 07, 2023 11:53 am
-
- 2
- 188
-
by bw1982
Wed Aug 16, 2023 12:45 pm
-
-
Torque tube mounting bolt size Attachment(s)
by Workinprogress » Fri Feb 11, 2022 8:24 pm » in Farmall Cub - 3
- 230
-
by Nelson 634
Sun Feb 13, 2022 1:54 am
-
-
-
Crankcase Cover Plate Bolt Size Attachment(s)
by TN_Cub » Tue Aug 09, 2022 11:38 pm » in Farmall Cub - 10
- 227
-
by JohnMihevic
Wed Aug 10, 2022 3:49 pm
-
-
- 9
- 349
-
by tnestell
Tue Nov 22, 2022 6:24 am
Who is online
Users browsing this forum: Leewebb7 and 4 guests