Page 2 of 2

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 4:21 am
by KETCHAM
It is know that L :shock: :shock: KS don't win the tug!!!! I like it though!!!! Kevin

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 6:04 am
by Kirk-NJ
John(videodoc) wrote:you oughta see the truck go up, when i am loading. gonna have to put some blocks under the trailer back end when i load this one.

By all means put the blocks under the back of the trailer. I busted a spring shackle doing just that. Of course the tractor I was loading was a tad heavier then your cub. My new trailer has down riggers on the back to keep that from happening again so I don't have to carry blocks any more.
That's one good looking tractor!

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 9:58 am
by Super A
Barnyard wrote:As the owner of a dually Cub that has pulled in the Tug, I can tell you the extra tires and weight will rob you of most of your power. :(


All things being equal I don't think the duals themselves cost that much power. I have never seen a figure on it in print anywhere, and as common as duals on farm tractors are, I would think it would be talked about more if it was a big issue. IF there is noticable power loss with duals, I expect there are some engine issues he would need to address. If it were me though, I would put all the wheel weights on the inside tires if they would fit.... :wink: That would put less strain on the finals.

I would think with 1200 lbs of weight, or close to that, wheel slip will be mighty close to zero. Might well run out of power well before it runs out of traction, but it should definately put on a good show! :sunning:

Al

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 6:42 pm
by HitNmiss1923
Very nice John, thanks for the info and good luck in the Tug..

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 10:10 pm
by Yogie
CharlieK wrote: i think yogie is already scarrreeeed!!

Charlie, I ain't only scarrreeeed but I'm afraid too. :shock:
Looks really nice John, can't wait to see it up close.
KETCHAM wrote:It is know that L :shock: :shock: KS don't win the tug!!!! I like it though!!!! Kevin

Kevin, just where were you last year when that pretty paint jerked a good knot in a few tails. :wink:

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 10:15 pm
by Barnyard
Yogie wrote:Kevin, just where were you last year when that pretty paint jerked a good knot in a few tails.

From what we could tell, it wasn't the paint that was pullin' that Cub!

Re: Ready for CUB TUG

Posted: Sun Feb 19, 2012 10:22 pm
by Yogie
Barnyard wrote:
Yogie wrote:Kevin, just where were you last year when that pretty paint jerked a good knot in a few tails.

From what we could tell, it wasn't the paint that was pullin' that Cub!

:bellylaugh: :big afro:

Re: Ready for CUB TUG

Posted: Mon Feb 20, 2012 7:22 am
by coppersmythe
having driven that cub down the track the day before the tug , i can say without doubt, the paint ,the motor,the tires ,the AIR in the tires, were pulling on that machine :-:-): . fine looking cub videodoc. i'm not experienced enough to known the "tricks of the trade", but i'd sure give it a run. i'm thinking of a few things to try myself :wink: .coppersmythe...........................................................PS: if that trophy ever got down this far , it may not want to go back up to the frozen north :lol: (not so frozen this year?).

Re: Ready for CUB TUG

Posted: Mon Feb 20, 2012 8:14 am
by Steve Butram
Kevin, just where were you last year when that pretty paint jerked a good knot in a few tails. :wink:



He was sitting under the blue tarp nursing his sun burn. That might have clouded his Vision. :lol:

Re: Ready for CUB TUG

Posted: Mon Feb 20, 2012 8:46 am
by John(videodoc)
And the "fish story tales" have already started. And think we are only 5 months away from the event.

Re: Ready for CUB TUG

Posted: Wed Feb 22, 2012 6:49 pm
by hpierce
Nice looking Cub John. Just wondering, is that the Cub the loader is going on?

Harlan

Re: Ready for CUB TUG

Posted: Wed Feb 22, 2012 6:55 pm
by John(videodoc)
Nope loader going on #4 demo. Freshest one out of the shop. Don't think loader would work with duals and all those weights