Middleborough Mass Cub Fest-Feb. 25th

[scotlem]

I'm planning to come, No projects, just Ed's head.

[ScottyD'sdad]

I'm planning to come, No projects, just Ed's head.

No, he's not a "shrink". He removed a broken water neck bolt, from a head, and is returning it. Ed

[scotlem]

Right, Ed's head

[Barnyard]

Let me see if I have this right, Scot removed a neck bolt from Ed's head. Hmmm...didn't Dr. Frankenstein do the same to his creation at one time or another?

[Buzzard Wing]

Sometimes I think Ed's head may be over-torqued, that would explain his 'sense of humor'.

Looks like the schedule is open for me....

If I can figure out how to get the engine off the long stripe and in the truck we could pull the front pulley and check the 'alignment' of the crank. I am leery of the main caps and the crank needs to be ground/cut regardless.

[spaceghost]

Attendees-
Ed D (ScottyD's Dad)
Bob Phillips (Spaceghost)
Chris W. (CapeCodCubs)
Bob Perry (bobperry)
Jim Perry (JimDawg)
Scoot L (Scotlem)
Larry Davis (Buzzard Wing)
Ross

It is going to be a good day

Last edited by spaceghost on Wed Feb 22, 2012 6:39 pm, edited 1 time in total.

[ScottyD'sdad]

How about Ross, is he bringing the cub for the front seal job? E (overtorqued head)d

[ScottyD'sdad]

[quote="Buzzard Wing"]Sometimes I think Ed's head may be over-torqued, that would explain his 'sense of humor'.

Larry, you could be right! That explains a lot! E(overtorqued head)d

[Bob Perry]

Sometimes I think Ed's head may be over-torqued, that would explain his 'sense of humor'.

Looks like the schedule is open for me....

If I can figure out how to get the engine off the long stripe and in the truck we could pull the front pulley and check the 'alignment' of the crank. I am leery of the main caps and the crank needs to be ground/cut regardless.

Larry if you need a hand let me know. Could shoot over there Wed. or Fri. night. Sounds like a good project that others could learn from !

[CapeCodCubs]

Man oh man my password to log on is jammed up, lucky to have been able to get on here now. But I still am having trouble reseting my password to what it always had been. See you all then.. I tried to get my friend Fred to come up but he is busy on his organic farm up in New Hampshire. I will bring my TC unit and hopefully after all this time get it rebuild, I have all the parts and it is ready to go.

[Bob Perry]

Recently I mounted a snow-blower to a Cub. The project is in its final stages, the main thing left is to get its 16 hp engine running. So that's what I'll be working on. I'm bringing just the engine bolted to a pallet.

When its done it will be pretty cool, with electric start / choke / throttle / clutch control up where driver can reach, even the spout turns by hydraulics. Hopefully we get a good late-winter snowstorm soon to give it a good test.

[Winfield Dave]

Recently I mounted a snow-blower to a Cub. The project is in its final stages, the main thing left is to get its 16 hp engine running. So that's what I'll be working on. I'm bringing just the engine bolted to a pallet.

When its done it will be pretty cool, with electric start / choke / throttle / clutch control up where driver can reach, even the spout turns by hydraulics. Hopefully we get a good late-winter snowstorm soon to give it a good test.

[Bob Perry]

K Dave gimme a week !

[ScottyD'sdad]

K Dave gimme a week !

Dave, he'll probably post a picture of you, driving it! Ed

[Bob Perry]

K Dave gimme a week !

Dave, he'll probably post a picture of you, driving it! Ed

Ed you best not give me ideas

But it was pretty cool looking down at your place as we returned from our trip to Sneads FL and Valdostsa GA !!!

Last edited by Bob Perry on Wed Feb 22, 2012 12:59 pm, edited 1 time in total.