I am going to cut down some trees, assuming they do not hit the house, I want to use the trees in someway. No need for firewood so I thought I would cut into boards. Problem is: no sawmill. I know I could buy or rent a sawmill but what would be the fun in that.
I thought about making a bandsaw mill, looks simple but I have no ready access to the large tires needed for the wheels.
So I thought I would make a reciprocating mill from a bowsaw blade, # 50 chain, sprockets, etc.. but would need approx 15 inch diameter crankshaft to move the blade. I think it would work well, slow, lots of vibration.
Last thought was for a chainsaw mill. I hate noise so I would power the chain with a 3.5 to 6.5 hp engine, mount on a frame similar to a bandsaw mill. I have read both good and bad about the chainsaw mills. I do not care if they are slow since the process would be automated for each board, I would not stand there while the board was cut but would be doing other things and come back to the mill when a board was done, reset, and cut another.
Anyone with any experience with this type of mill? Speed? Smothness of cut? For planks or beams or will it cut fine enough to make boards.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
sawmill
-
- 10+ Years
- Posts: 1172
- Joined: Tue Oct 19, 2004 7:10 am
- Zip Code: 29130
- Tractors Owned: fcub(5)
tricycle cub
154 (4)
Earthmaster (2)
JD 40T, JD 420 crawler-loader, JD MT
JD Unstyled A, Styled A, Unstyled AR
JD H
Centaur Tractor
AC Model C, G
Cub Cadets (9)
Gibson D
Red-E - Circle of Safety: Y
- Location: SC, Ridgeway
- Super A
- 10+ Years
- Posts: 5234
- Joined: Mon Jan 26, 2004 10:53 am
- Zip Code: 28521
- Tractors Owned: Collector of Super As, Corn Pickers, and a buncha other junk. Even a Cub now and then...
- Circle of Safety: Y
- Location: NC, Jacksonville area
Re: sawmill
There is probably someone in your area with a portable mill that would come cut your logs. My notion is those chainsaw mills are probably hard to get an accurate, uniform cut. Plus someone with a mill has enough experience sawing that he can get the most out of each log, meaning fewer slabs to throw away. My dad is having some cut now, that were blown down by the hurricane. Don't know what the guy charges but it's reasonable.
Al
Al
White Demo Super A Restoration Updates
Let us pray for farmers and all who prepare the soil for planting, that the seeds they sow may lead to a bountiful harvest.
Celebrating 75 years of the Super A: 1947-2022
Let us pray for farmers and all who prepare the soil for planting, that the seeds they sow may lead to a bountiful harvest.
Celebrating 75 years of the Super A: 1947-2022
- Bigschuss
- 10+ Years
- Posts: 445
- Joined: Wed May 14, 2003 7:08 pm
- Zip Code: 01256
- Tractors Owned: 1984 JD 990
1953 JD 40S
1973 JD 300 Snowmobile - Location: Savoy, MA
Re: sawmill
I've got experience with chainsaw mills. Last summer I tried cutting my own spruce 6x6's for my timber frame project. I found that the bar on the chainsaw was just not rigid enough to provide a nice square beam. I would get something that was basically square, but when I checked it with a framing square I realized it was just not adequate. I ended up having a local sawyer cut my beams from my spruce for really a fraction of the cost of buying them.
For cutting boards you might be O.K., as squareness won't be a factor. Be sure to get the special ripping chain. The finish comes out very nice...kind of a smooth to midly rough-sawn appearance.
Some of the guys with the portable sawmills charge a delivery and set-up fee. I checked into that before I had my logs done. One guy charged $300 just to show up. For a big order involving days of milling, I guess it would make sense. But to have a dozen or so logs milled, I don't think the portable guys are cost effective.
Just to give you a ballpark....I had fifteen 12' to 14' spruce logs milled into 6x6's and 4x6' plus a huge stack of 2x4's and 2x6's and 1x material for about $100. I transported my logs to the sawyer on a flatbed trailer....made 2 trips.
Hope this helps.
Blair
For cutting boards you might be O.K., as squareness won't be a factor. Be sure to get the special ripping chain. The finish comes out very nice...kind of a smooth to midly rough-sawn appearance.
Some of the guys with the portable sawmills charge a delivery and set-up fee. I checked into that before I had my logs done. One guy charged $300 just to show up. For a big order involving days of milling, I guess it would make sense. But to have a dozen or so logs milled, I don't think the portable guys are cost effective.
Just to give you a ballpark....I had fifteen 12' to 14' spruce logs milled into 6x6's and 4x6' plus a huge stack of 2x4's and 2x6's and 1x material for about $100. I transported my logs to the sawyer on a flatbed trailer....made 2 trips.
Hope this helps.
Blair
I wish coke was still cola, and a joint was a bad place to be...
- Merle Haggard
- Merle Haggard
- Mr E
- Cub Pro
- Posts: 5762
- Joined: Mon Jul 30, 2007 11:48 am
- Zip Code: 32460
- eBay ID: noles1432460
- Circle of Safety: Y
- Location: FL, Sneads
- Contact:
Re: sawmill
I had some Cherry logs sawed by a local sawyer. The guys charged me strictly by the board foot plus a $25.00 setup fee for transportation. Did a great job.
In the middle of every difficulty lies opportunity. - Albert Einstein
.
Roy Edenfield
Deep South CubFest #10
February 14 & 15, 2020
.
Roy Edenfield
Deep South CubFest #10
February 14 & 15, 2020
-
- Team Cub Mentor
- Posts: 20377
- Joined: Fri Jul 02, 2004 9:52 pm
- Zip Code: 65051
- Circle of Safety: Y
- Location: Mo. Linn
Re: sawmill
Couple of thoughts.
There is a saw mill about 2 miles from the property and they buy logs. Might be worth while to just sell the logs.
At one of the local antique power shows they set up a saw mill and cut logs during their demonstrations.
There is a saw mill about 2 miles from the property and they buy logs. Might be worth while to just sell the logs.
At one of the local antique power shows they set up a saw mill and cut logs during their demonstrations.
I have an excuse. CRS.
- grumpy
- Cub Pro
- Posts: 2780
- Joined: Tue Jan 10, 2006 12:03 am
- Zip Code: 15522
- Circle of Safety: Y
- Location: PA. Bedford (Centerville)
Re: sawmill
I have a nephew that can tell you what happens when you leave the mill to its self while you do "other things". Wouldn't want you to get hurt or destroy all of your hard work. Keep us posted and good luck with your project. Grump
David Dee Mock-Leonard
Nothing is foolproof to a sufficiently talented fool.
Some days it's not worth chewing through the restraints
Nothing is foolproof to a sufficiently talented fool.
Some days it's not worth chewing through the restraints
-
- 10+ Years
- Posts: 916
- Joined: Sun Feb 02, 2003 10:44 pm
- Zip Code: 60936
- Tractors Owned: 47 Cub SN 8664
48 Cub
50 Demo
54 Cub
3-55 Cub
2-56 Cub
55 LOBOY SN 876
57 LOBOY
58 French Cub
2- 60 LOBOY
69 Cub
54 Super M
42 H
48 H
57 300LP
57 450
Cub Cadet 123
Cub Cadet 149 - Circle of Safety: Y
- Location: Gibson City, IL
- Contact:
Re: sawmill
At least in my area, but some shows have a saw mill they opperate all day during their shows. You could prolly get them to mill them for cheap?
My .02 worth.
My .02 worth.
Who is online
Users browsing this forum: No registered users and 8 guests