Tools and Reviews to help your fellow Cubber's.
Moderator: Team Cub
Unwarranted FLAME reviews will be deleted without notice. Members are encouraged to exhaust all arbitration efforts with the companies before posting negative reviews here.
FarmallCub.Com and the moderators are not responsible for member reviews of businesses and attractions.
Send issues regarding reviews to Cub@farmallcub.com.
10 posts • Page 1 of 1
I am looking to get a blaster set up, I have a 5hp 80 gal 17 cfm compressor. I have a small bucket blaster but the sand is always getting clogged up in the hose. It is as if it is sucking in all the sand at once. So which is better, the tank or open bucket version?
I did start to just pull it out of the bucket one day, it worked better for a while but soon it was back to the same old same clog and nothing comes out.
Suggestions, should I try to reduce to hole in the bottom of the bucket some? just a thought to get it to the point where it won't pull so much sand.
Just a couple of suggestions. Your sand must be perfectly dry for any blaster to work, regardless of the type. So make sure your media is dry. Also, it is important that you have some means of removing moisture from your compressed air system. Both of these moisture sources will cause clogging problems.
Last edited by Don McCombs on Fri Apr 05, 2013 6:13 pm, edited 1 time in total.
MD, Deep Creek Lake
"1950 Something" Farmall Cub
1977 International Cub w/FH
1978 International Cub
1948 Farmall Super A
1951 Farmall Super C w/FH
Also make sure there are no small rocks to clog it. I filter my sand with screen when I put it in tank
I have a 10 gal. pressure tank sandblaster and it works very well for small jobs. One thing that really improved the operation was the addition of a small bowl type desiccant dryer. I picked up one from McMaster-Carr. The other thing I like about it is the desiccant can be removed, dryed in an oven and re-used. It does an excellent job of reducing moisture in the compressed air. Prior to that I was using filter type dryers with a couple of moisture traps in the piping runs, but the air line near the nozzle plugged frequently.
I have a small moisture seperator so maybe I get a bigger one. I have used this little bucket blaster for 5 yrs and it seems I fight with it every time. So I was just wondering if I need to switch blaster units or not for better success.
....or move to Colorado where dessicants, rust, and moisture problems are not in the vocabulary.
"We don't need to think more,
we need to think differently."
The ideal air system has as long a run as possible from the compressor using iron pipe with a pitch to it and a good drip leg with a drain valve. A filter set with a final desiccant that can be regenerated is the ticket as suggested and that should come off the vertical line going down to the drip leg. Sand blasting gobbles air and the pipe run gives a chance to condense out moisture to lighten the load on the dryer train that usually condenses in the tank under smaller demand. Then you need to size the blast nozzle to match your air supply- but is sure sounds like moisture is the issue.
Most of the open bucket type systems I have seen, have a hole in the side of the fitting that goes into the bucket. Make sure the suction hose is not covering that hole.
"The Constitution is not an instrument for the government
to restrain the people, it is an instrument for the people to restrain the
government lest it come to dominate our lives and interests." Patrick Henry
I would suggest Texas Blaster if you want a good quality pressurized unit, they are pricey, but very well made ( here in the U. S. oF A . ) if you can imagine that.
I started out with nothing and now I only have half of that left !
I run my blast cabinet with 200 feet of hose and 3 traps one at the cabinet , drain your tank of water on a regular basis. that may solve your problem, or at lest help it
IN GOD WE TRUST
All others pay cash
Power corrupts; absolute power corrupts absolutely byJohn Emerich Edward Dalberg
10 posts • Page 1 of 1
Who is online
Users browsing this forum: No registered users and 1 guest