Does anyone know where I can get steel plates that I can use with lag bolts to connect heavy timbers together?
I'm restoring an old farmhouse and barn. The barn is a 30x40 bank barn, and I had to jack up the (second) floor joists to replace the (non-existant) sills, and level out the floor. The entire floor is supported by 6x6 timbers that run horizontally beneath the floor joists on either side, supported by vertical 6x6 beams standing on top of poured concrete footings. Everything is being held together by the weight above, but I'd like to stabilize the connections. I've seen plates in magazines that look to be 1/8 to 1/4 inch thick steel, with holes for lag bolts to pass through. But I've never seen them in any supply houses. Any leads would be appreciated.
Thanks
Paul
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
Steel Brackets for Post and Beam Construction
-
- 10+ Years
- Posts: 565
- Joined: Mon Apr 07, 2003 11:35 am
- Location: Morristown, New Jersey
Steel Brackets for Post and Beam Construction
51 Cub; IH 340 Utility; IH 240 Utility http://public.fotki.com/PWS/
- beaconlight
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
Go to a scrap yard. Not just an auto one. you will be able to get plate and serious sized angle. Then cut and put the drill press to work. I would use through holes and double plates or at least backup washers. Thehardware they use on piers or the top of electric poles is what you want. Are they all sawn timbers you are working with? Many old barns used timbers with flats at the joints or only on two sides.
Bill
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
-
- 10+ Years
- Posts: 565
- Joined: Mon Apr 07, 2003 11:35 am
- Location: Morristown, New Jersey
The timbers are oak, and are sawn on all sides - my next door neighbor has a portable sawmill and he cut them all.
Were you thinking finding scrap pieces of 1/4 inch plate and burning out rectangular pieces to make the brackets? I considered that, but since I have 12 posts, I need 24 plates. That's (at least) 100 - 1/2 inch holes! I was hoping for an easier way.
The beams have been sitting as they are for a couple of years since we did the jacking. I suppose it would take an earthquake to knock it all apart, but it seems like I should have the junctions tied together. Obviously, there hasn't been a building inspector involved. . . .
Were you thinking finding scrap pieces of 1/4 inch plate and burning out rectangular pieces to make the brackets? I considered that, but since I have 12 posts, I need 24 plates. That's (at least) 100 - 1/2 inch holes! I was hoping for an easier way.
The beams have been sitting as they are for a couple of years since we did the jacking. I suppose it would take an earthquake to knock it all apart, but it seems like I should have the junctions tied together. Obviously, there hasn't been a building inspector involved. . . .
51 Cub; IH 340 Utility; IH 240 Utility http://public.fotki.com/PWS/
- Brent
- 10+ Years
- Posts: 1055
- Joined: Thu Feb 06, 2003 9:21 am
- Zip Code: 93510
- Location: Acton Ca.
Paul,
I built a pole barn for my horses. I found a local steel fabricator that cut the plates and saddles I needed. He was also able to punch all the holes. I had 30 plates and 10 saddles made and the total cost was about $75.00.
I think because he had the equipment that could shear the steel and could stamp the holes rather than drill each one kept the cost down. Might want to try that. You might also try your local steel supplier. I know the supplier by me has what it sounds like you are looking for already made.
I built a pole barn for my horses. I found a local steel fabricator that cut the plates and saddles I needed. He was also able to punch all the holes. I had 30 plates and 10 saddles made and the total cost was about $75.00.
I think because he had the equipment that could shear the steel and could stamp the holes rather than drill each one kept the cost down. Might want to try that. You might also try your local steel supplier. I know the supplier by me has what it sounds like you are looking for already made.
Always try the easiest thing first.
- beaconlight
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
Thats a good idea but i still think you need through bols or rods not lag screws. May be some more experienced than I am can weigh in on this.
Just remembered that I have seen barn rebuilders and restorers and supplies for same some where on the internet.
Bill
Just remembered that I have seen barn rebuilders and restorers and supplies for same some where on the internet.
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
- Jim Hudson
- 10+ Years
- Posts: 1224
- Joined: Sun Feb 02, 2003 1:11 pm
- Zip Code: 28001
- Location: Albemarle, North Carolina 28001
-
- 10+ Years
- Posts: 251
- Joined: Sun Feb 09, 2003 10:05 pm
- Location: MS, Oxford
Hey Paul,
I will do some checking Monday. I have a bother that is in the home/building construction business and I know he has used items
like I think you need and I will check with him. Also, in the meantime,
if you are not going to double the plates you may want to go to a
lumber salvage yard and most will have some of the backing plates.
I know you have seen them. Many are in the shape of a star or some
other shape and range in many sizes. I think I have seen a show on
the Old Yankee Workshop sereis using this item. You may get a lead
on their website.
Hope this helps some and I will try to get more info.
I will do some checking Monday. I have a bother that is in the home/building construction business and I know he has used items
like I think you need and I will check with him. Also, in the meantime,
if you are not going to double the plates you may want to go to a
lumber salvage yard and most will have some of the backing plates.
I know you have seen them. Many are in the shape of a star or some
other shape and range in many sizes. I think I have seen a show on
the Old Yankee Workshop sereis using this item. You may get a lead
on their website.
Hope this helps some and I will try to get more info.
- Rick Prentice
- Team Cub Guide
- Posts: 5636
- Joined: Mon Nov 01, 2004 7:24 am
- Zip Code: 43528
- Tractors Owned: 47(circle cub),48(Floyd backhoe),49,,51,54 and another 55
- Circle of Safety: Y
- Location: OH, Holland
- Contact:
For a different approach. Why not pick up some wood dowel and glue and just angle drill some holes, glue up the dowel and drive them in. It should be just as fast as driving lags. It will be alot cheaper and will look primitive, too. That's how they use to do it.
When I told my dad I've been misplacing things and doing stupid stuff----His reply---"It only gets better"
- beaconlight
- 10+ Years
- Posts: 7703
- Joined: Thu Aug 19, 2004 2:31 pm
- Zip Code: 10314
- Location: NY Staten Island & Franklin
When they dowled it was a willow dowl through a tenion in a pocket. Though the angle drill and dowl you suggest would work well if done from 2 oposing angles.
Bill
Bill
Bill
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
"Life's tough.It's even tougher if you're stupid."
- John Wayne
" We hang petty thieves and appoint the great ones to public office."
- Aesop
-
- 10+ Years
- Posts: 565
- Joined: Mon Apr 07, 2003 11:35 am
- Location: Morristown, New Jersey
I agree with BeaconLight that through bolts connecting two plates sandwiching the wooden post would be much better than lag bolts holding plates independently from each side. But how do you drill a hole that size, through 6 inches of oak, and keep the hole straight enough to hit the exact spot on the other side to be able to meet the opposing plate's hole? And do it corrext each time to be able to make up 4 bolts on each plate!! I've just never been able to do it, even for one hole, and particularly now that the posts are in place.
I'd love to hear any tips or suggestions.
Thanks
I'd love to hear any tips or suggestions.
Thanks
51 Cub; IH 340 Utility; IH 240 Utility http://public.fotki.com/PWS/
-
- 10+ Years
- Posts: 661
- Joined: Wed Mar 05, 2003 9:09 pm
- Zip Code: 18603
- Tractors Owned: 1948 Cub
1955 Cub - Location: PA, Berwick
- Contact:
Paul. You can use your bracket/plate with the holes in it to pilot & drill thru and then use large washers on the reverse side. This way the holes don't have to match up with holes on the reverse side. Drill, then bolt one hole at at time. OR If you must sandwich between two plates, drill halfway thru on both sides and hammer (small sledge) the bolt thru the hole! Don't know exactly your design or technique, but this should work.........
Ron
Who is online
Users browsing this forum: No registered users and 8 guests