I'm looking for a cross over bearing number for the pto lever bearings the Ih part number is IH-59769-C92 is there any other source than going to IH to get the them??? Can these be interchanged with another bearing?
I also need new seals for my 3260 mower deck the IH part number is #473428-R92 again is there any source or is there another seal that interchanges?
I ordered the bearings and seals but its been since the spring and i haven't got them yet. The first frost will be here by the time i get her running then i'll seafoam her up for the winter.
This site uses cookies to maintain login information on FarmallCub.Com. Click the X in the banner upper right corner to close this notice. For more information on our privacy policy, visit this link: Privacy Policy
NEW REGISTERED MEMBERS: Be sure to check your SPAM/JUNK folders for the activation email.
PTO CLUTCH lever ball bearings???
Forum rules
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
Notice: For sale and wanted posts are not allowed in this forum. Please use our free classifieds or one of our site sponsors for your tractor and parts needs.
-
- 10+ Years
- Posts: 7388
- Joined: Sat Jul 22, 2006 5:02 pm
- Zip Code: 00000
- Location: in northern usa
PTO CLUTCH lever ball bearings???
I'm technically misunderstood at times i guess its been this way my whole life so why should it change now.
-
- 10+ Years
- Posts: 26
- Joined: Mon Jul 19, 2010 2:46 pm
- Zip Code: 12764
Re: PTO CLUTCH lever ball bearings???
I would think a NAPA or other parts place could cross over to a BSA bearing and a National seal without a problem. I've measured them up and found them that way also.
-
- 10+ Years
- Posts: 7388
- Joined: Sat Jul 22, 2006 5:02 pm
- Zip Code: 00000
- Location: in northern usa
Re: PTO CLUTCH lever ball bearings???
Ok i'll try my old napa store.
I'm technically misunderstood at times i guess its been this way my whole life so why should it change now.
-
- 10+ Years
- Posts: 259
- Joined: Mon Jan 12, 2004 9:58 pm
- Location: CNY
- Contact:
Re: PTO CLUTCH lever ball bearings???
Bill, You will have to get the exact same bearing with the snap/retainer rings in the outside race. There are several varients of that bearing and most do not have these rings. I will look tomorrow to see if I have my old ones lying around still. If I do the numbers were on the brgs.
If I remember right the correct ones were not much different pricewise at Napa than Case/IH.
If I remember right the correct ones were not much different pricewise at Napa than Case/IH.
-
- 10+ Years
- Posts: 259
- Joined: Mon Jan 12, 2004 9:58 pm
- Location: CNY
- Contact:
Re: PTO CLUTCH lever ball bearings???
Bill I checked around and could not find the old ones but I did find they are a SKF 6007 series.
That makes it 35mm ID x 62mm OD x 14mm W
Looking in my BCA book it looks like a BCA 107FFL (sealed both sides with outer snap ring ) would work.
Here is a link to one
http://cgi.ebay.com/1-FAFNIR-9107PPG-Ba ... 0641242252
That makes it 35mm ID x 62mm OD x 14mm W
Looking in my BCA book it looks like a BCA 107FFL (sealed both sides with outer snap ring ) would work.
Here is a link to one
http://cgi.ebay.com/1-FAFNIR-9107PPG-Ba ... 0641242252
Return to “Lo-Boy Series - 154, 184, 185”
Who is online
Users browsing this forum: No registered users and 7 guests